ta motor drives a solid 3/8" diameter steel shaft at 3,600 RPM, see Fig. below. Calculate the following G-10 Msi.) a) Maximum shear stress in shaft b) Angle of twist (end A vs. end B) c) Maximum shear strain in shaft material d) Maximum normal stress in shaft material e) Maximum normal strain in shaft material Motor 3/8 Bearing 40

ta motor drives a solid 3/8" diameter steel shaft at 3,600 RPM, see Fig. below. Calculate the following G-10 Msi.) a) Maximum shear stress in shaft b) Angle of twist (end A vs. end B) c) Maximum shear strain in shaft material d) Maximum normal stress in shaft material e) Maximum normal strain in shaft material Motor 3/8 Bearing 40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A full circular cross-section shaft will be designed to provide power transmission at 220 (revolution/minute) revolution of a 12300 kW engine. Since the shaft length is 3 m, the material shear modulus is 80 GPa, and the shear yield stress is 190 MPaa) How many kN.m torque should the shaft carry?b) Write down the minimum safe shaft radius in metersc) How many rad is the shaft at the specified minimum radius. found?
RSL-2 A rod of negligible mass is pulled down at each end as shown to the right. The rod is supported by a rope as shown. a) Draw the free body diagram for the rod on a figure like the one to the right. support rope b) Find the net torque on the rod about the point where the rope supports it. 2ft 5ft c) Which way does the rod tend to rotate, clockwise or counterclockwise? 35lb 15lb d) Which way does the angular acceleration vectora point? 99+ bp
Solid Mechanics A steel shaft in the form of a solid body circular rod or a circular tube can be manufactured. Torsion of spindle of 1200 N.m it is required to carry the moment. Anti-slip protection for shaft material stress 40 MPa, the largest permitted unit torsion angle in the bar 0.750 / m and the shear modulus of the steel is G = 78 GPa. a) Find the required diameter d0 for a solid circular shaft. b) Required for a ring-section shaft whose thickness is one tenth of the outer diameter Find the outer diameter d2. c) Diameter ratios (d2 / d0 for ring and solid section shafts. Find the weight ratios with the ratio).
A circular tube is having a 50mm outside diameter and a 40mm inside diameter and 0.5m long. 1) Find the angular torsion of the tube formed shaft, when 100 kW is transmitted at 1000 rpm. The shear modulus (modulus of rigidity) is 80,000 N/mm². 2) Find the diameter of the solid cylinder having the same torsional stress. Formula 1) 3) Tmax = Te J J = 1 ac ² T Trin C1 J=17(c²-c₁) Φ =Σ and t = P Co p T-IP Tp J TiLi i Ji Gi Power Tw w in rad/s
A simply supported shaft arrangement is shown in the figure. A solid shaft of 50 mm diameter made of low-carbon steel is used. Given values are: X;=762 mm X:=1016 mm X3=508 mm PA=356 N Ps=534 N Solution: Determine first critical speeds: a) 1155 rpm b) 648 грm a) Unloaded shaft b) Rayleigh method с) 651 грm c) Dunkerley method
4) Two 20º full depth steel gears are heat treated to BHN = 350. Pinion turns 860 rpm. N₁-24; N₂=96; Pd=4 and b=2". Find the horsepower the gears are transmitting when b) AGMA Quality No 9 c) AGMA Quality No 10 In the figure below the gears are 20° full depth of AGMA Quality No 9. a) Find the horsepower transmitted by the 1-2 mesh b) Find the required width b for the 3-4 mesh if they are carrying the same horsepower as the 1-2 mesh. No.2, C.I. BHN=220 P=4, N₂=72,b=2" No 1, Steel, P=4, N₁=24,b=2"" n₁ = 570 rpm /No.4.CL. BHN = 220 P=3, N₂=72 No.3, Steel, P=3, N₁=24
ach student has been allocated a different shaft length, L and a different allowable maximum shear stress,τmax and subject to a different Torque, T. For steel use a shear modulus, G=80,000 MPa.A steel shaft L meters long is subjected to a torque T. If the shear stress is limited to τmax, calculate:a) The minimum shaft diameter required.b) The angle of twist over the length of the shaft.c) The Power output if your shaft is rotating at 2000 rpm. L=1.9m τmax=95MPa T=1.5kN-m
Compute: a.) The maximum shear stress developed in a 6 inch diameter solid steel shaft that transmits 600 HP at a speed of 80 rpm. b.) The shear stress if the speed were increased to 300 rpm. Answers: a.) 11,146psi b.) 2,972 psi I'm unsure of how to solve this problem. Please help me understand how to solve for these answers ste-by-step. Thank you in advance.
For the steel beam is used to support the loads shown below: a) Draw shear force diagram and bending moment diagram. b) Determine the magnitude and location maximum moment. c) Calculate the maximum stress at point B. 1G Kn 2 kN/m 10 kN 25 2.5 20 cm A B to to 5 m 3 m 2 m 10 cm
From the following diagram find with k1=20N/m, k2=30 N/m, k3=25 N/m, k4=35 N/m, k5=50N/m and k6=60N/m, m=10kg A) the equivalent spring B) the displacement C) the work performed
1) A compression spring has square edge and ground ends. The total coil number Inside dia. 50 mm of spring is 12 and Brinell Hardness number is HB=380. The free length of the spring is 200 mm. The spring is assembled into a machine by compressing, when the machine runs, the spring is compressed 100 mm. 5 mm a) Is the spring likely to buckled. b) Would this spring developed a 5 mm permanent set if compressed solid? c) What is the critical frequency? 0,80 0,70 0,60 both ends against flat plato 0,50 0.40 buckling zone 0,30 - 0,20 0,10 no buckling zone 0,00 10 LIID Running length 100 mm Assembled length 180 mm Free length= 200 mm
A torque is applied to advance a single-lead 3/4 inch ACME thread upwards. The downward axial load is 240 Ibs. The coefficient of friction in the thread is 0.175. The applied moment is: a) 19.248 in-lb b) 19.517 in-lb c) 19.802 in-lb d) 20.149 in-lb e) 20.421 in-lb f) 20.736 in-lb