a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3.b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R =1092, L=20 mH, and a = 60°. Determine:i. An expression for the load current.ii. The average load current.iii. The power absorbed by the load.iv. Sketch the graph of the output waveform.VsS₁S4Figure$3$₂LoVo

Given data Full-wave bridge rectifier contains a source voltage of Vs=120 V. Supply frequency, f=60…

a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R 1002, L-20 mH, and a 60°. Determine: Vs i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. S₁ S4 S3 S₂ Figure 3 Io Vo LEKT

a) Explain the operation of the controlled full-wave bridge rectifier shown in figure 3. b) The controlled full-wave bridge rectifier shown in figure 3 has a source 120 V rms at 60 Hz, R 1002, L-20 mH, and a 60°. Determine: Vs i. An expression for the load current. ii. The average load current. iii. The power absorbed by the load. iv. Sketch the graph of the output waveform. S₁ S4 S3 S₂ Figure 3 Io Vo LEKT

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
92) For three - phase half-wave Controlleed rectifier Shown in he figure: 1. Derive a fomu la for mean load Voltage. 2. praw the wave form of vo, i,,i, iy and voltage across thyristor 1 (r.) assuming highly inductive load and d = 120
For the single phase half-wave rectifier, the source is a sinusoid of 120 V rms at a frequency of 50 Hz. The load resistor is 5ohm. Determine (a) the average load current, (b) the average power absorbed by the load and (c) the power factor of the circuit.
The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
92) For three- phase half-wave Controlled rectifier Shown in the figure: I- Derive. a formula for mean load Voltage. 2- Draw the wave forms of vo, Li,i, o and voltage across thyristor1 (r.) assuming highly inductive loud and d = 120 Vo
H.W: - For a single phase half wave uncontrolled rectifier if the input supply voltage is (v,= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings: - i. Draw the rectifier circuit. ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. iv. If the load is (R=102), then determine the mean and rms values of the current.
A half-wave rectifier with ohmic load given in the figure below feeds a 50 Q load and the peak value of the source voltage is 311V and the frequency is 50 Hz. Accordingly, find the following desired circuit parameters: a) Effective (rms) voltage of the source, b) the peak current of the load, c) Average stress of the load, d) Average current of the load, e) The effective (rms) voltage of the load, f) Effective (rms) current of the load, g) Power of the load + vD R
Consider a 3-phase half-wave rectifier circuit shown in the figure. The source is a symmetrical, 3-phase four wire system. The line- to-line voltage of the source is 150 V and the supply frequency is 300 Hz. The ripple frequency at the output is R ER B N-
For the half-wave rectifier, the source is a sinusoid of 120 V rms at a frequency of 60 Hz. The load resistor is 5 ohm. Determine (a) the average load current, (b) the average power absorbed by the load.