Q3 Betermine the values of K and a such that the damping factor is 0-6 and a settling time of 1-675 ec →Y(5) -BT R(S) K 5+2 b) Find the value ad K and a such that S =0.6 and ess for sleep import is 0.25. (102)

Q: Consider the circuit shown below and answer all of the following questions. t = 0 10Ω 2. V. = 8 V 20…

A: Circuit is given as,

Q: Q(1): Determine whether the system below is stable or not ? G(s) = 240 (s+1)(s+2)(s+3)(s+4) R(s)…

A:

Q: The unit step sequence is defined to be the causal sequence un=1 forn20. Plot the sequences 241)…

A:

Q: 2. Find the transfer function between R[s] and Y[s] in the given block diagram. Gf LEHET Gr Hi [p]…

A: Given Data:The give block diagrm with node numbers is given by,To Find:The transfer function .

Q: A discrete time signal x(n) is shown in figure below x(n)f 1 -2 -1 o 1 2 3 4 Sketch the signal…

A: we will draw the u(2-n) then we multiply with x(n) to get required signal .  u(2-n) = u(-n+2)…

Q: It is aimed to obtain the Vo(t) output signal from the circuit to which the Vi(t) input signal will…

A:

Q: Haw Man MOS Transistats are refuited to imtlement He functon F: CAC)+ CAB) - CAB'C"

A: CMOS A complementary metal-oxide-semiconductor is made up of two semiconductors that act in opposing…

Q: dV« (0') dVcz(0*) di, , (0*) Find the following initial conditions: and dt dt dt

A:

Q: Determine the transfer function for the system shown in Figure Q3. R(s) G₁ + H₁ H3 G₂ Figure Q3 G3…

A:

Q: is R Vo L VL Vin

A: From the circuit:

Q: In the circuit given below, R1=7Q and R2 = 7 Q. 1 H ll 4u(0) А R1 R, NOTE: This is a multi-part…

A: It is given that: R1=7Ω and R2=7Ω

Q: Q8/ To design a counter which count in the following sequence 0,1,3,5,7 by * using T- F.F, the input…

A:

Q: Q9 The discrete-time signals x1[n] is shown in the figure. Carefully sketch each of the following…

A:

Q: Determine the values that should be used for both K1 and K2 so that the step response of the…

A:

Q: A single-phase load is supplied through a 35 kV feeder whose impedance is (95+j360) Ω and a 35 / 2.4…

A: Given Feeder voltage Vf =35 KV Feeder impedance Zf =(95+j360) Ώ Transformer rating = 35/2.4 KV LV…

Q: The following cireuit is part of an audio systan , If we wont to transfer max pawer to the 8S…

A: Find Re

Q: Question 1 Find the convolution by the graphical method for if 2/9 1/3

A: Given: Consider the following signals: To find: Find the convolution by graphical method.

Q: A discrete time signal x(n) is shown. Sketch and label carefully each of the following -2 -1 | 2 3 4…

A: In this question we need to sketch the given signal.

Q: Determine the output Cr(s) due to the input R(s), when R(s) is a unit ramp function. D(S) (3) Select…

A: Given data: The given diagram is shown below,

Q: Vo(s) A(s) 6 s+3 compute the voltage vo(t) at the steady-state for a(t) = 5 sin 3t, (A, s). H(s) =

A: Introduction A transfer function is a mathematical representation that describes the relationship…

Q: Q9 The discrete-time signals x1[n] is shown in the figure. Carefully sketch each of the following…

A:

Q: Consider the continuous-time LTI system 2y"(t)-5y' (t)-7 y(t) = -3x"(t) + 11x(t) (a) Find the…

A:

Q: andwidth and signal frequency 1 KHz. The quantizing step size is 250 mV. Find the power of e massage…

A:

Q: Find the following function as a sum of min terms and product of max terms F(A,B,C) =BD’+AD+BD

A: Solving the given expression:

Q: 43. For the system in the given figure, R(S) G₁ (s) C(s) R(S) G₂ (s) H₂(s) C(s)

A: Solution is given below !!

Q: R, ww R, ww out ROM For represented circuit sketch s-domain equivalent and compute the condition of…

A:

Q: Problem 4 dVc« (0*) dVcz(0*) di (0*) CI C2 L1 Find the following initial conditions: and dt dt dt C1

A:

Q: Which variable is error in the following D) 6- E(s) H(s) Y(s) O A) U(s) B) O ) E(s) D(s) D)

A:

Q: The figure on the right has a slower steady-state response. Step Response Slep Response 16 1.4 08…

A: The solution is given below

Q: To design a counter which count in the following sequence 0,1,3,5,7 by * using T-F.F, the input of…

A: The required counter can be designed by using the State transition table and the simplified Boolean…

Q: x0,1 Q#1 y#1 Dis the next value of Qin the FSM described by the state diagram above. Which of these…

A:

Q: Enter the value of resistance (R)=12 Enter the value of Capacitance (C) =9 Enter the input voltage…

A:

Q: Find Gensul of this R-L-C -Crcuit ! C=0,0833 F E= 10v R=22 ell しニ2H

A:

Q: state space modeling and analysis ex find the state and output equations. ci + 4 c - 3 c₂ = C2 + ci…

A: For the given differential equations it is asked to find the state and output equations

Q: 7. Consider the system having transfer given by: K G(s) = s(s + 4)(s+4+ j4) Determine the breakaway…

A: Break away point is the solution of dk/ds=0 From given transfer function we will find k and the…

Q: (s+0.02)(s+6.25) G(s) = The compensator circuit (active) given the function at the bottom will be…

A: Given: The compensator circuit (active) given the function: To find: If C2=0.8 micro Farad, which…

Q: Q8/ To design a counter which count in the following sequence 0,1,3,5,7 by using T- F.F, the input…

A: