A cooling curve is shown determine (a) the pouring temperature, (b) the solidification temperature, (c) the superheat, (d) the cooling rate just before solidification begins, (e) the total solidification time, (f) the local solidification time, (g) the undercooling, and (h) the probable identity of the metal. (i) If the cooling curve was obtained at the center of the casting sketched in the figure, determine the mold constant, assuming n = 2. 1000 900 800 700 600 500 400 300 200 100 Temperature (°C) 2 4 6 2 in. a 2 in. 2 in. 8 10 12 Time (min)

A cooling curve is shown determine (a) the pouring temperature, (b) the solidification temperature, (c) the superheat, (d) the cooling rate just before solidification begins, (e) the total solidification time, (f) the local solidification time, (g) the undercooling, and (h) the probable identity of the metal. (i) If the cooling curve was obtained at the center of the casting sketched in the figure, determine the mold constant, assuming n = 2. 1000 900 800 700 600 500 400 300 200 100 Temperature (°C) 2 4 6 2 in. a 2 in. 2 in. 8 10 12 Time (min)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) From the figure of cooling curve find the following: (a) Pouring temperature (b) Cooling rate (c) Solidus temperature (d) Super heating (e) Super cooling (f) Solidification range 800 (g) Local solidification time (h) Total solidification time 600 400 8 10 Time (min) 2) From the figure of cooling curve find the following: (a) Pouring temperature (b) Cooling rate (c) Liquidus temperature (d) Solidus temperature (e) Super heating (f) Super cooling (g) Solidification range 300 (h) Local solidification time 200E (i) Total solidification time 100 4. 8 12 16 20 24 28 32 36 Times (sec) Temperature (°C) Temperature (°C)
A cube shaped casting solidifies in 5 minutes. The solidification time in minutes for a cube of the same material, which is 8 times heavier than the original casting will be (A) 10 (B) 20 (C) 24 (D) 40
Q6 Use the Iron carbon diagram to find 4 of the following. ( 1- The range of solidification temp. (start to end of solidification) for cast iron with 3% C. 2- The solid and liquid percent for Cast Iron with 2.7%C at 1320 °C. 3- Draw the expected microstructure at room temp. for hypo-eutectoid steel with 0.7%C. 4- Draw the expected cooling curve from the melting point to room temp. for cast iron with 4.3%C. 5- The steps and the allotropy change for steel with 0.01%C.
With a solidification factor of 0.97 × 106 s/m2. the solidification time (in seconds) for a spherical casting of 200 mm diameter is (a) 539 (b) 1078 (c) 4311 (d) 3233
2) The region showing planar growth during solidification near the fusion zone boundary will exhibit O High temperature gradient and high growth rate High temperature gradient and low growth rate Low temperature gradient and high growth rate O Low temperature gradient and low growth rate
/The total solidification times of three casting shapes are to be compared: (1) a sphere with diameter= 10 cm, (2) a cylinder with diameter and length both = 10 cm, and (3) a cube with each side = 10 cm. The same casting alloy is used in the three cases. (a) Determine the relative solidification timesfor each geometry. (b) Based on the results of part (a), which geometric element would make the best riser? (c) If the mold constant = 3.5 min/cm2 in Chvorinov's rule, compute the total solidification time for each casting.
what solidification time is required for a casting of 9.5 cm3 and a mold contact area of 10 cm2? The mold constant is 838 s/cm2.
Under uniform cooling, a spherical casting of 25 mm diameter undergoes volumetric solidification shrinkage and volumetric solid contraction of 2.5% and 6.2%, respectively. Determine the diameter of the casting after solidification.
(b) What are the factors that affecting the freezing rate during solidification of the molten metal and evaluate why nearly all metals experience shrinkage during solidification process.
A solid cylinder of diameter D and height equal to D, and a solid cube of side L are being sand cast by using the same material. Assuming there is no superheat in both the cases, the ratio of solidification times of the cylinder to the solidification time of the cube is (a) (L/D (c) (2D/L)2 (b) (2니D)2 (d) (D/L)²
what are the stages of solidifaction in a casting process? when do those happen?what is under cooling?
Two cubical castings of the same metal and sizes of 2 cm side and 4 cm side are moulded in green sand. If the smaller casting solidifies in 2 mins, the expected time of solidifications of large casting will be (b) 2/8 min (a) 16 min (c) 8 min (d) 4 min