A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given Es= 2 x 105 N/mm and Ec= 1.2 x 105 N/mm2

A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given Es= 2 x 105 N/mm and Ec= 1.2 x 105 N/mm2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 17 mm and an elastic modulus of E = 71 GPa. The steel rod has a diameter of 18 mm and an elastic modulus of E = 190 GPa. Assume a = 3.1 m, b = 1.7 m, and c = 0.9 m. What is the magnitude of load P that is necessary to displace point A 8 mm to the left?
- An aluminum right-circular cylinder surrounds a steel cylinder as shown. The axial compressive load of 200 kN is applied through the rigid cover plate shown. If the aluminum cylinder is originally 0.25 mm longer than the steel before any load is applied, find the normal stress in each when the temperature has dropped 20 K and the entire load is acting. For steel take E = 200 GPa, a = 12 x 10-6/° C, and for aluminum assume E = 70 GPa, a = 25 x 10-6/° C. 200 kN Ans. ost = 9 MPa, oal = 15.5 MPa 80 mm- 85 mm- 141 mm. 500 mm
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given E = 2 x 105 N/mm² and E= 1.2 x 105 N/mm².
If the average rainfall intensity for 50 years of records is 50 mm/h (2.0 iph) for storm duration of 60 min and the coefficient of variation of the data is 0.324. Compute the theoretical rainfall intensities for the return periods of 2, 5, 20, and 100 years. Assume that the log-probability law is applicable. Show complete solution.
I need to solve the question of strength materials
4
A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of eachmaterial are shown in the figure. A fixed support is rigidly attached to the right end of thebronze rod. Determine the stress each section in KPa.
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. A 12500*pi В) 6250*pi C) 3125*pi 1563*pi
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 63 GPa. The steel rod has a diameter of 24 mm and an elastic modulus of E = 215 GPa. Assume a = 4.2 m, b = 1.4 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 13 mm to the left?
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.