A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given E = 2 x 105 N/mm and E = 1.2 x 105 N/mm².

A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given E = 2 x 105 N/mm and E = 1.2 x 105 N/mm².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

GIVEN: Bar has a cross-sectional area of 4 in? and is placed between two rigid immoveable supports when it is 30.00 inches long at a temperature of -20°F. REQ’D: A) The stress in the bar at 90°F if it were made of steel. Esteel = 10 x 10° psi asteel = 13 x 106/°F B) The final length of the aluminum bar
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C NANTSELEINE Steel: A = 900 mm² E = 200 GPa L=1.5m Bronze: A=1200 mm² E=83 GPa L=2.0m What is the ratio of the elongation of steel to bronze? O 0.367 O 0.433 O 0.467 0.333
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. b C P Steel: A = 900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0m E= 200 GPa L = 1.5m What is the value of P without exceeding the allowable stress of steel, in kN? 250 340 280 O230
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b C P Steel: A-900 mm² Bronze: A=1200 mm² E = 83 GPa L=2.0 m E = 200 GPa L=1.5m What is the value of P without exceeding the allowable stress of bronze, in kN? O 161 O 174 O 145 124 4
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c = 1.7m. b C P Steel: A=900 mm² E = 200 GPa L=1.5m Bronze: A 1200 mm E=83 GPa L=2.0m What is the value of P without exceeding the allowable stress of bronze, in kN? 174 145 161 124
2. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming that the rods were initially stress-free. What is the largest load P that can be applied without exceeding stresses of 160 MPa in the steel rod and 65 MPa in the bronze rod? - 2.5 m 2 m 2 m Steel A=1000 sq. mm Bronze A=400 sq. mm E=200 GPa E=83 GPa L=1.6 m L=2.2 m P
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3