25 KN III a a ASTEEL ACOPPER STEEL 2.8 m 3.6 m hree vertical rods of equal distance, each has a diameter of 20mm and supports a load of 25 kN as shown in the figure. Initially, all the rods are adjusted so that they share equal tresses. Neglecting any chance of buckling, and taking Es = 205 GPa and Ec = 100 GPa, determine the final stress in the steel when a further load of 20 KN is added.

25 KN III a a ASTEEL ACOPPER STEEL 2.8 m 3.6 m hree vertical rods of equal distance, each has a diameter of 20mm and supports a load of 25 kN as shown in the figure. Initially, all the rods are adjusted so that they share equal tresses. Neglecting any chance of buckling, and taking Es = 205 GPa and Ec = 100 GPa, determine the final stress in the steel when a further load of 20 KN is added.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

10
jp
Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A and loaded as shown. Which of the following gives the maximum average normal stress in the system shown? 6P 4P A5.5 P/A B.4.5 P/A 3A 2A A 3P C.4 P/A D.3 P/A 4P 6P Which of the following is the highest value of stress within the strain hardening region of a typical elasto-plastic material subjected to tensile test? A. Elastic Limit B.Yield Stress C.Ultimate Stress D.Proportional Limit What is the lateral strain of a uniaxially loaded member if its longitudinal strain is 0.02 and its Poisson's ratio is equal to 0.3? A.+0.006 B.-0.006 C.+0.667 D.-0.667 Which of the following is the highest value of stress within the elastic region of a typical elasto-plastic material subjected to tensile test? A.Yield Stress B.Elastic Limit C.Ultimate Stress D.Proportional Limit
The working load P on the propped cantilever shown are each 150 kN. If the yield stress of mild steel is 300 MPa, determine the plastic section modulus in cubic millimeters, using a load factor of 1.75 against collapse. (express your response this way, x,xxX,XXX.X). Pu Pu 1.1 2m B A 2m 2m
determine the minimum thickness of the steel bar. answer set c only
In a steel flat plate a state of plane stress available. Calculate o, and principal stresses if 0₁-140 N/mm², p=0.25, 1₁,-40 N/mm², e,- -3.6 × 10 and E-2× 10³ N/mm².
A high-strength steel band saw, 29 mm wide, runs over pulleys 900 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 290? Assume E = 210 GPa. Answer must be in mm.
A high-strength steel band saw, 27 mm wide, runs over pulleys 1000 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 350? Assume E =230 GPa. Answer must be in mm.
I need the answer as soon as possible
During the tension test, the wooden specimen is subjected to an average normal stress of 2 ksi. Determine the axial force P applied to the specimen. Also, find the average shear stress developed along the section Ɵ -a of the specimen.
Pls answer as indian code practice
According to IS 800-1962 the permissible bending stress in steel slab plate is (b) 1420 kg/cm² (d) 1890 kg/cm² (a) 1500 kg/cm² (c) 2125 kg/cm²