A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?

A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt. - omega for source in rad/s? - omegaR for circuit? -XL? -XC? -phi in radians? -Z? -imax?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Cost of a 600 kW wind turbine is $ 550000. Other initial costs including that for installation and…

A: Given Power PR =600 kW capacity factor =CF =0.25 number of years n=20 interest rate I=5% =0.05 land…

Q: Let εR = 6, μR = 8, and σ = 0. If Jd = 25sin(1.04 x 105t - 5x) az μA/m2, find E(t=1.5, x = 2.1).

A: In this question, We need to determine the E(t=1.5, x = 2.1). If εr = 6, μr = 8, and σ = 0. If Jd…

Q: 5 procedures in building a sustainable lamp

A: Procedures in designing a sustainable lamp system or lighting system is as follows: 1) Choosing the…

Q: A basic d'Arsonval movement with internal resistance of 1002 and half scale current deflection of…

A: In this question we need to design a multirange voltmeter by using Direct and indirect method

Q: Q1: A particular intrinsic semiconductor has a bandgap energy of 1.32 eV and has a resistivity of 60…

A: We need to find out resistivity for given semiconductor .

Q: H.W: A series motor has an armature resistance of (0.2 0) and a series field resistance of (0.3 2).…

Q: What is the minimum length of antenna required transmit a radio signal of frequency 20 MHz? O a.…

Q: Power amplifier delivers 3.6 W of power to a load. The input signal power was 200 mW. What is the…

A: We need to find out power gain

Q: Problem 3 Find the characteristic equation and its roots for the circuit shown. 10 µF 1 mF

A: Steps to find The Roots and CE Convert circuits into s domain from the time domain Do the…

Q: Problem [11] Obtain the current i(t) for t>0 in the circuit below. t=0 40 2 30 2 ww ww 80 V 3F 0.5i…

A: In this question we need to find a current i(t) for t > 0

Q: What value of input resistance is needed in the given circuit to produce the given output vo R; ww…

Q: 5.47 The transistor in the circuit of Fig. P5.47 has k, = 0.4 mA/V², V, ation at the edge of…

A: We need to prove tha given equation for saturation region

Q: A system has an open-loop transfer function given by K/[s(1 + 3s)]. Which one of the following…

A: Given data, System with OLTF OLTF=Ks1+3s

Q: 2- Design a mulirange with (5o, 150, 280)U? sol : -3 Vm = 30 * 10 m2= 50 10 1666-666 %3D Vm 30 m2 =…

A: In this question we will design multi range voltmeter....

Q: What are the two ways in which an alternating waveform differs from DC?

Q: The figure below shows one of the consumer circuits with three electrical appliances R, S and T,…

A: As per the guidelines of Bartley we supposed to answer first three subpart only

Q: What value of input resistance is needed in the given circuit to produce the given output voltage ?…

A: We need to find out input resistance for given circuit

Q: #4 FIND (1), t>0 120 36V 2H

A: Solution is as follows

Q: Q2: a) The instantaneous expression for the magnetic field intensity of a uniform plane wave…

A: We need to find out phase constant and location at which magnetic field is zero

Q: If the load is resistive, then the power factor will be O 1 Leading O Lagging

A: Considering the power formula, S=P+jQ S is apparent power P is active power Q is reactive power

Q: The magnetic tield intensity; in webers per m?, at a distance of 10 cm from a wire carlying a…

A: We need to find out magnetic field.

Q: 68 R1 A 130 B R3 R2 L2 V1 C1 V+ 11 86 8mH C 182nF L1 12mH

Q: t= 0 i(t) R 20 t= 20ms L Vbat 10V v(1) 400mH

Q: A basic d'Arsonval movement with internal resistance of 1002 and half scale current deflection of…

A: To extend the current range of Ammeter, connect a small shunt resistance in parallel To extend the…

Q: ELECTRONIC VOM R3 mA 3.3K 15m Adc 3 Rs 1K 0-20vdc M, 0-0.1mAde Fig. 17-3

A: If the resistor R5 is open then current doesn't flow in open circuit. The current flowing in the…

Q: Q2:- A semiconductor material has electron and hole mobilities un and up respectively. When the…

A: We need to find out conductivity

Q: Problem [8] Find the Thevenin impedance of the circuits at its output terminals. -j2 2 10 Ω + V.…

Q: 1. NUMBER SYSTEMS 1.1. Given the following number system with all of its symbols as follow: (0. 1.2,…

Q: b) A lk resistance is connected across the secondary winding of a 200V/400V transformer with the…

Q: A coaxial cable with inner radius 0.97 mm and outer radius 3.12 mm has a dielectric for which ϵR =…

A: FormulaD=εoE+PInterms of εrD=εrεr-1×P

Q: region D = 6ax + (-8)ay + (5)az nC/m2 has a relative permittivity of 1.21. Find |∇V|.

A: We need to find out magnitude of gradient of potential .

Q: 4. Using superposition, find the sinusoidal expression for the voltage vc for the network of Fig.…

Q: A 4.7 Micro-Farad capacitor is in series with a 470 K-Ohm resistor with a 12V power supply. How long…

A: Given, A series RC circuit in which C=4.7 μFR=470 kΩVS=12 V

Q: The figure shows the excitation curve (including residual voltage) of a 170 kW, 250 V DC shunt…

A: Given curve is for 850 rpm rated current. Nrated =850

Q: Problem 1 From the given circuit, determine v, for all time interval when Vs = 30 [u(-t) + u(t –…

A: In this question, We need to determine the Voltage Vc if time to = 5ms.

Q: y F

Q: roblem 3 nd the characteristic equation and its roots for the circuit shown. 10 10 μF Vs 1 mF

Q: 10 V 20 V 3Ω -4 V Please find Select one: O a. 2 O b. -2 O .4 O d. -3 O e. 3

Q: Find the Thevenin equivalent at terminals a-b of the circuit shown below. What is the value of the…

Q: 1- A 9.1V Zener diode at test current of 28 mA. The incremental resistance is 52. Find Vzo and the…

A: In this question we will find zener voltage at given current.....

Q: For the circuit shown, calculate the value of Vout. You may assume that Vs = 10.5 V, R1 = 5 kN, R2 =…

A: The operational amplifier is an important voltage amplification electronic circuit with very high…

Q: For the circuit shown below, the initial conditions are zero, Vdc is a voltage source continuous and…

A: As per the guidelines of bartleyby I need to answer first three subparts only so kindly repost other…

Q: Explain how an oscilloscope may be use to display a current waveform.

A: Solution is as follows

Q: 2. Find the mechanical power output of the 185 W, 110 V, 60 Hz, single-phase induction motor whose…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: In a unity feedback control system with G(s) : 4 when subjected to unit step input, it is required…

Q: . What effect does changing the frequency on the effective value of sinusoidal voltage? 2. What…

A: Consider a sinusoidal voltage voltage shown below, Here v=Vmsinωt The peak voltage is Vm and ωt=α…

Q: Quit A Source Voltage Source of ou rimis in Sevies with an internal resistanc of 2kn in Connecte d…

A: In this question, We need to determine the turn ratio? And maximum power to the load? Pmax = V2…

Q: For the circuit given below, and find the formulas for: Vout a. Output voltage gain, which is…

A: for our policy, i can solve first three parts

Q: What is the minimum length of antenna required transmit a radio signal of frequency 20 MHz? a. 3.75…

A: Given data, Frequency of radio signal, f=20 MHz

Q: rom the given circuit, determine ve for all time interval when Vs = 30 [u(-t) + u(t – to)] 5 ms to =…

Concept explainers

Capacitor

The capacitor is an element used to store electrical energy in the electrical field. A capacitor is a form of passive energy.

Question

A circuit is designed with an AC source of max voltage 12 and frequency 60 Hz. The circuit has a resistance of 1050 Ohms, an inductance of 0.06 Henrys, and a capacitance of 0.009 coulombs per volt.

- omega for source in rad/s?

- omegaR for circuit?

-XL?

-XC?

-phi in radians?

-Z?

-imax?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
A resistor & a capacitor are connected in series across 230V, ac supply. The current taken by the circuit is 4 A for 50 Hz frequency. The current is reduced to 2 A, when the frequency of supply is decreased to 40 Hz. Determine the value of resistor & the capacitor.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
A capacitor in series with a 200 ohms resistor draws a current of 0.3 ampere from 120 volts, 60 hz source. What is the value of the capacitor in microfarad? a. 8.7 b. 9.7 c. 6.7 d. 7.7
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
Let's say you measure t1/2 to be 0.037 seconds and the resistance in the circuit is 68 Ohms. Then what is the capacitance in micro Farads? Answer in micro Farads.
A) find Ztot in rectangular form B) find Ztot in polar form C) find V1 or VL in polar for. ( use voltage divider rule or ohm law).
In a series circuit with the following devices to a 230volts 60Hz supply with a resistor in the range of 300 ohms and 990 ohms. What are the steps in calculating the impedance ...
Which of the following is true about all series ac circuits?(a) The voltage across any circuit element is a maximumwhen the current is a maximum in that circuit element.(b) The current at any point in the circuit is always thesame as the current at any other point in the circuit.(c) The current in the circuit is a maximum when thesource ac voltage is a maximum.(d) Resistors, capacitors, and inductors can all change thephase of the current.
What impedance vector (0- j15) Ohms represents:A. A pure resistance. C. A pure capacitance.B. A pure inductance. D. An inductance combined with a capacitance.
1. Enumerate five formulas for series-parallel capacitances across Vt source and draw the circuit. 2. Enumerate five formulas for parallel-series capacitances across Vt source and draw the circuit.