A centrifugal water pump with a suction pipe is shown in Figure 3.5 Pump output is Q=0.03m³/s, thediameter of suction pipe d=250mm, vacuum pressure that the pump can reach is p(og)=6.9 mH2O, and allhead losses in the suction pipe hw=1.5mH2O. Determine the utmost elevation he from the pump shaft to thewater surface on the pond.he0.Figure 3.5 Pumping water

A centrifugal water pump with a suction pipe is shown in Figure 3.5 Pump output is Q-0.03m'/s, the diameter of suction pipe d=250mm, vacuum pressure that the pump can reach is p,(pg)=6.9 mH¿O, and all head losses in the suction pipe hw=1.5mH2O. Determine the tutmost elevation h. from the pump shaft to the water surface on the pond.

A centrifugal water pump with a suction pipe is shown in Figure 3.5 Pump output is Q-0.03m'/s, the diameter of suction pipe d=250mm, vacuum pressure that the pump can reach is p,(pg)=6.9 mH¿O, and all head losses in the suction pipe hw=1.5mH2O. Determine the tutmost elevation h. from the pump shaft to the water surface on the pond.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as shown in figure below. Diameter of the pipe is D= 16 cm. (Patm=100 kPa, Ywater-9810 N). Please answer the following questions. (1) Zmax a) Determine the flow rate of the system. b) Determine the maximum elevation of the highest point of the piping system without causing cavitation (Zmax=?).
I need the answer as soon as possible
Addtl Qs. Determine the flow in line DC
14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is 0.200 m³/s. The head loss due to major and minor friction losses is given by the equation, h₁ = 12.0 2g V 25 m Pump Determine the pump head. Also determine the shaft work done by the pump.
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
A 1 2 The three-reservoir system is shown below: 3 C The elevation of Reservoir at A is 140m and at Cis 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f - 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) - 400mm Determine the elevation of Reservoir B in meters.
Water flows from Resorvoir A (Elev 133 m.) to a turbine (Elev 76 m.) then discharges into tailtrace B (Elev 30 m.) as shown. the head loss from (A) to (1) is 2 times the velocity head in the pipe, and the head loss from (2) to (b) is 1.49 times the velocity head in the pipe. if the flow rate in the pipe is 35 ft63/S, diameter of all pipes is 25 in., calculate the horsepower generated by the turbine. Use 1 hp = 550 lb-ft/s.
In a nozzle shown in the figure, the fluid is Gasoline (p = 719 kg/m3, 9 = 4.06 x 10-7m²/s, P=2500 Pa, e=0.5mm and Q= 0.1 m3/s). Find the diameter of the pipe? %3D Elev, =82.65m . Elev. 66.66m 965.5m Lec. Sumayah Amal al-din Majeed
Please correct answer And solve both part