For the flow net shown below, the soil is isotropic having a permeability of 0.002 cm/sec. Determine the following: - seen The flow rate in m'/day/m length. b. The pore-water pressure at point P. The factor of safety against piping. (e 0.7 and G, 2.7). a. 1-Gs Tte с. 1oueく 15 m 0-7m 4-5m 15m impervious HNF stratum

For the flow net shown below, the soil is isotropic having a permeability of 0.002 cm/sec. Determine the following: - seen The flow rate in m'/day/m length. b. The pore-water pressure at point P. The factor of safety against piping. (e 0.7 and G, 2.7). a. 1-Gs Tte с. 1oueく 15 m 0-7m 4-5m 15m impervious HNF stratum

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.14P

See similar textbooks

Similar questions

In fig. FV = Water --? If the tank width is 5 m (into the paper) 4m 0 5m C 5m B 1941.6 N 1941600 KN 1941.6 KN
Problem 6: EGL and HGL (II) Part A Why is the energy gradient (i.e., the slope of the EGL=EL) larger in pipe 2 than in pipes 1 or 3? (<10 words) Part B Why are the EGL and HGL not parallel in this figure? (<10 words) H V² 28 HGL 2 EL Hydraulic grade line, slope = S, Ax - Energy line, slope = Sy Bed ylope Datum h₂ - Az 2 4 X
15. If the pressure in pipe A is 6 kPa, the SG = 0.85 pressure in pipe B =. ........... psig. Water 90 mm 30% a. 1.27 70 mm b. 8.73 40 mm C. 60.17 SG = 13.6 Mercury d. None of all these
A conduit is carrying oil ( S = 0.75 ) and its absolute viscosity is 0.25 kg / m-s. If the flow rate is 0.45 cu.m/s Determine the following • The entrance length • The length of the inviscid cone • The length of the profile development given the following situations 1. Circular pipe 800mm 2. rectangular pipe (Width = 800mm, Depth 1200mm)
(a) A groundwater borehole at USM engineering campus contains 3000 mg/L of TDS. The flow is 0.32 m3 /s. The design TDS concentration of the product water is below 400 mg/L. The net pressure is 40 atm. The membrane manufacturer provides that the membrane has a water flux rate coefficient of 2.2 x 10-6 s/m and a solute mass transfer rate of 1.5 x 10-6 m/s. Calculate the membrane area required for the RO system. (B) A water treatment at Nibong Tebal receiving a raw water contains a concentration of 0.5 µg/m3 atrazine from Kerian River. In order to comply with the drinking water quality guideline, the treatment plant should reduce the concentration of Atrazine to 0.1 µg/L. If the dosing of powdered activated carbon have been applied before the coagulation, calculate the minimal dose of PAC in mg/m3 .
H.W.9/7 For the closed tank with Bourdon-tube gauges tapped into it, what is the specific gravity oi thE On ana une pressure reading on gage C? Soil = 0.87 0.5 m Air PA= 50.0 kPa 1.0 m Oil S = 0.8) PB = 58.5 kPa 0.5 m 1.0 m Water 0.5 m Pc=? T= 10°C
CrHstal Original at water dişam klater at 290k flaos thiou h tube of diameter 1-8mm voilts a pressure drop of 800N/m. he vis Cosily and density of wstoy at agok are 1-080 xio S/m² and loskalm? respectuity tind the mass flaw rate through the tabe i) befermine the flow regime of the water flow.
Earth dam homage material has the fllows data K=0.0005cm/sec level of top of the dem= 200m bed level of the dam =1.78m filter length=25m free beard=2.5mu/s slope=3:1 D/s slope =2.5:1 determine the phredic line for this dam and the discharge casing through the dam (casingrande of flownet)
9.10 Ferrous sulfate is used as a coagulant and Eme as a coagulant aid at a water treatment plant. The specific gravity of the floc and adhered sus- pended material is 1.005 at a temperature of 10°C. Determine: a The overflow rate in m³'d-m if the flow is 26,500 m/d and the clarifier is 18.29 m by 36.57 m. 6 The settling rate in cm/s for the overflow rate in part (a).
(ii) For the rectangular septic tank in (i) above, prove or show that the efficiency of particle settling is independent of depth and retention time. and is given by V. Q/As, where Vo= Surface loading rate, Q = Flow rate and As = surface area of tank. (iii) micr
An oil of viscosity 8 poise flows between two parallel fixed plates which are kept at 60 mm distance. The pressure drop over the length of 150 cm is observed to be 4.5 kPa. The width of the plates is 0.2 m. The discharge of flow (in Ips) is [Assume laminar flow.]
A cast-iron pipe transports water from a reservoir A and discharge it into air through a rotary valve at alocation 100 m below the water surface elevation at the reservoir.a) Draw the HGL and the EGLb) Determine the discharge if the temperature of the water is 10°C. Consider minor losses.