Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the reservoir surfaces is 80 m. and pipe friction factor is 0.024. K1= 0.5 for the pipe entrance,K2-D1.O for exit and K3= 1.0 for valve as shown in fig. " Valve (K 1.0) Water 15 C 2000 m M0-em-dia. concrete pipe

Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the reservoir surfaces is 80 m. and pipe friction factor is 0.024. K1= 0.5 for the pipe entrance,K2-D1.O for exit and K3= 1.0 for valve as shown in fig. " Valve (K 1.0) Water 15 C 2000 m M0-em-dia. concrete pipe

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2) For the pipe system shown in the figure, the flow rate is 0.00085 m³/s & v-1.14*106 m²/s, F-0.023, p=990 Kg/m³, diameter 15mm, Celbow=0.9, Cvalve -10, Cfaucet -2.Calculate the pressure at point (1)? -3.0- Faucet 4.5- -1.5- 3.0 Valve EXE 3.0 elbow 005
A B 3. Pipe no. Diameter (mm) Length (m) Friction factor Q (I/s) 1 75 120 0.018 15 l/s 2 100 150 0.020 125 180 0.022 Compute Q2, Q3 and total Q
enough pro Fuck T Question 3 Water flows at a velocity of 1.5 m/s in a 200 mm new ductile iron (CH = 130) pipe. Estimate the headloss over a kilometer length of pipe using: (a) The Hazen-Williams equation (b) The Manning formula (n=0.012) (c) The Darcy-Weisbach equation (assume temperature of 20°C) 3gd
Question 7 A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 120 (Hazen-Williams) Pipe 2 n = 0.020 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 3 in meters.
Q4: Assuming f-0.020, determine the discharge in the pipes. Neglect minor losses. Pipe Diameter AB 250 mm 200 mm 400 mm BC BD Length 1200 m 600 m 200 m EL.45m EL 3m. B C EL. 3.0m D EL 0.0m
3. A 30m long, 20mm diameter steel pipe is used to drain an oil tank determine the discharge 3E when the oil level in the tank is 4m above the exit of the pipe. Neglect minor losses, (assume f = 0.12) 4m D-20 mm, L-30 m, t 0.12
- Determine the total head loss hf from A to o in U the susem shown in the figure iF the discharge is |. G0 m ls. Assume f=002 for all pipes 450 mm &, G00m qoomm &, 900m 750mmo,450m IC GO mm & ,720m D
orI (P=880 k9 /m ) Flow under head 3o min Pr Pe (L= 3000 m of Cooling Viscosity a long the PiPo length Will Chanje and equal to o.s Pa-s for ISoo m and 1. 14Pa.s for the Yemain length of PiPe Prove tha t the flow is laminar and find the f low ra te . , D= 0- 3 m) becanse %3D
Question 7 2 pts A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 100 (Hazen-Williams) Pipe 2 n = 0.015 (Chezy-Manning) Pipe 3 f = 0.020 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 3 in meters.
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
Q2: An otl of viscosity Co.15 pas) and specific gravity 0.9 is flows Throngh 1.Find The slope of The Pipe That will canse The Pressure to be constantalong The pipes entire length? an inclined (300mm) diameter Pipe. Q= 0.005m3/sec 3oomm Dia. Zz datum 2. check if The Rlow is laminarRlow?
A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 90 (Hazen-Williams) Pipe 2 n = 0.015 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 3 in meters.