solve it thankyou A billboard BF is subjected to wind pressure of 1200N per meter at B tozero at F as shown. Determine the components of hinge forces at A and C.2 m4 m4 m4 mA6 m6mWN 00Zt For the truss shown, determine the forces in bars BD, CD and EF.Use Method of SECTIONS.800 N800 N800 NaBaG.

“Since you have asked multiple questions, we will solve the first question for you. If you want any…

Answered: A billboard BF is subjected to wind…

A billboard BF is subjected to wind pressure of 1200N per meter at B to zero at F as shown. Determine the components of hinge forces at A and C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Why is calculus needed for hydrostatic pressure and force application problems?
F P F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.
Use three decimal places and no need to input the unit. A 14-in-diameter hollow sphere of steel (SG = 7.85) has 0.16 in wall thickness. How much weight must be added inside to make the sphere neutrally buoyant? (lbf)
The piston diameter of a 6-stroke 1-cylinder gasoline engine is given as 4.25 inch mm, the piston stroke is given as 3.75 inch. Since the compression ratio of this engine is 9.5, find the stroke volume, combustion chamber volume and cylinder volume in cm3.
1. A 5 in diameter solid shaft is used to drive the propeller of a marine vessel. It is necessary to reduce the weight of the shaft by 60%. What would be the dimensions of a hollow shaft in mm if made of the same material as the solid shaft?
As per NPCP, a shower compartment or bath shall have a minimum interior area of 0.6 sqm and it shall be capable of encompassing a 762 mm diameter circle. What shall be the least possible length in millimeters of the shower compartment assuming it is rectangular in shape? (round off your answer to the nearest hundredth and write your answer in this format : 000.00 mm)
Provide and illustration to what is asked.
Q3/ including setting the machine, a worker manufactures 79 pieces of different tools in 7 hours and 15 minutes. If the standard time for the tool was Setting time = 40 min Production time per tool= 10 min Compute: 1-The standard time for manufacturing the 79 tools 2-Efficiency of operator
State one word problem and solve it wherein the ideal mechanical advantage of a wedge is being solved. Use the formula, IMA = (Length of the Widge) divided by (Width of the Wedge). note: please do not forget to include your solution in solving the problem.
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…
Please solve part B only
Paula has worked for Brindle Corporation for 3 years. During this time, she has worked as a machine operator/cell leader in various work cells. Recently, the plant went to mandatory 12-hour shifts and plans to remain on this schedule for several months. Paula’s present work cell is manufacturing 3-inch diameter exhaust tubes that are made from stainless steel. These tubes get a hole punched in them, a flange welded on, and burrs ground off. The pipe then gets placed into a gage to check that it was made correctly. (The tubes weigh about six pounds.) Paula has been performing the welding operation. She leans into the machine and loads the part into a fixture then positions the flange. Both pieces are clamped (using hand clamps) into position and the machine is cycled by depressing two palm buttons. The gaging operation requires placing the finished part into the gage and clamping it (using hand clamps) into place. A pin is depressed to verify the position of the hole and a…