Answered: A 5ft long bar with a 3in x 5in cross…

A 5ft long bar with a 3in x 5in cross section is subjected to a 13,638lb tensile load. What is the tensile stress in ksi? Answer to two decimal places.

Construction Materials, Methods and Techniques (MindTap Course List)

4th Edition

ISBN:9781305086272

Author:William P. Spence, Eva Kultermann

Publisher:William P. Spence, Eva Kultermann

Chapter3: Properties Of Materials

Section: Chapter Questions

Problem 4RQ: How does a tensile stress differ from a compressive stress?

See similar textbooks

Related questions

Q: 9-13. Determine the reactions at the supports. Assume A is a fixed and the joint at B is fixed…

A: Given:Required:Reaction at support

Q: If an SPT test gave the average blow count of 32 in fine sand below water table, then what is the…

A: Given that :-Average blow count of 32 in fine sand below water table Calculate the corrected value…

Q: Determine the load in each cable needed to support the 500 lb load 3 ft 6 ft B 6 ft· 13 ft 5 ft 6 ft…

A: Given:Required:Load in each cable

Q: Questions 1. Define specific gravity of soil. 2. What are typical values of specific gravity for…

A: given data,multiple questions are given regarding the specific gravity of soil.let's discuss about…

Q: A contractor needs 3715 m³ of aggregate base for a highway construction project. It will be…

Q: A tangent section of highway has a -1.0% grade and ends at station 4+75 and elevation 82 ft. It must…

Q: 1. In each case, establish a position vector from point A to point B. 1m 3m -4 m -4 m- B 3m

A: Given dataFig is given shows the axis x,y and zposition vector that represents the location of a…

Q: Problem, 3: Draw the shear, bending moment, and axial force diagrams and the qualitative deflected…

A: Given:Required:Axial force, shear force and bending moment diagram and qualitative deflected shape

Q: Each of the links AB and CD is made of steel (E = 29 x 106 psi) and has a uniform rectangular cros…

A: E = 29 x 106 psi Load = 10000 lb

Q: 1. Use Kani method to compute the end moments of the beam shown 300 lb (a) 200 lb/ft -10 ft- -10 ft-…

A: NOTE : Since you have asked multiple questions, we will answer the first question for you. If you…

Q: A circular secondary clarifier will be used to treat an average daily flow (ADF) of 6,000 m3 /d from…

A: Overflow Rate (OR) = 15 m3/ d. m2 Solids Loading Rate (SLR) = 100 kg/ d. m 2 Average Daily Flow…

Q: 1-30. A differential element taken from a curved bar is shown in the figure. Show that dN/d0 = V,…

A: Given data,Differential element taken from curved bar givenShow that

Q: Determine the maximum horizontal and vertical velocity at a depth of 2.0m for a wave with the…

A: Wave period Wave height Water depth Depth of interest

Q: What is Ax? OON A O 1200 N O 600 N O 800 N 2m 1200 N -6m

A: To find horizontal reaction at A

Q: Is the weakest point on a shear or moment diagram the point that has the most load?

A: The weakest section for shear can or cannot be the point of maximum loading particularly when…

Q: Determine the support reactions of the following frame using force method. Assume EA=GA=EI=1.

Q: How did 10 feet come up?

A: Given:Required:To explain how CB is 10 ft

Q: Q1. During a 60 seconds period, a loop detector is occupied by vehicles for the following times for…

A: Given dataperiod=60 secondloop dector is occupied is detected by the vehicles for the following…

Q: 1. Starting from the basic definition of stiffness. determine the effective stiffness of the…

A: Stiffness- It may be defined as the property of material by which the material is able to resist…

Q: A. All the member forces using the Method of Joints B. Axial force at member BE using the Method of…

A: A truss with loading is shown in the above figure. We have to find out the followings: Member forces…

Q: for the following project, answer the given questions. A- The expected duration. B- Total duration…

A: For a project, activities and their duration (optimistic, most likely, and pessimistic) are given…

Q: Draw the shear and moment of the following structures. 50 kN/m 30kN/m 30 EN сокола ..

Q: 4. Horizontal Curve: P.C. 12+00.00 P.I 4= 30° P.T. This highway has a 60 mph speed limit requiring a…

A: Speed Limit on highway Minimum Radius Station PC Radius Deflection angle

Q: Fee in member DJ of the Howe roof truss illustrated. N ect any horizontal components of force at the…

A: To find force in member DJ

Q: Q1/[B]: For the clayey sand shown in the figure, the saturated unite weight is 20.69kN/m³ and the…

Q: Develop an equation for the average velocity of a viscous fluid in a capillary tube of radius R…

Q: 9.15. The IDF function for 10- yr storms in Atlanta, Georgia, is given by i 1628 (t + 8.16)0.76…

A: maximum rainfall intensity occurs at 38% of the rainfall durationDuration= 40-min

Q: A clay layer 3m deep is sandwiched by a pervious material. The soil reaches 90% consolidation in 3…

A: Depth of clay layer = 3 m% consolidation in 3 years = 90 %To Find :The time taken by this layer to…

Q: A 16 × 20 in. column is made of concrete and reinforced with the same six No. 9 (in-lb) bars. The…

A: A 16 × 20 in. column is made of concrete and reinforced with the same six No. 9 (in-lb) bars. The…

Q: A 5-day BOD test if performed on an industrial wastewater sample that contains no bacteria;…

Q: 7.3 Compute the development length required for the top no. 9 bars of a cantilever beam that extend…

A: A cantilever beam is given we need to find out the development length for a. Straightb. Have a 90°…

Q: A 60 kip column is supported on a square footing with a length and base of 4 ft. Using the 2:1…

A: Given&nbsp;Load 60 kipWidth 4 ftDepth 5 ft2:1 methodTo find out Increase in stress

Q: In (Figure 1), F = {300i - 100j + 700k} N. Figure 2 m B 22: m Z -1 m 6 m 3 m < 1 of 1 Part A…

Q: 3-35. Determine the force in all the members of the lattice (complex) truss. State if the members…

A: Force in the vertical direction - Sum of the moment at the point A - from the equation 1,RA =…

Q: How does IoT technology impact the efficiency of waste management systems in urban areas?

A: IoT (Internet of Things) technology has a significant impact on the efficiency of waste management…

Q: A 400 m vertical curve connects a -2.00% grade to a +4.00% grade. The P.I. is located at station…

Q: Stress is an response to an External, Internal Internal, External External, External Internal,…

A: Stress can be defined as the internal resistance per unit area of the body.It is given by formula:…

Q: All questions regarding the proper disposal of hardous waste at the University of Toledo should be…

A: The Environmental Health and Radiation Safety Department at the University of Toledo is the primary…

Q: Calculate the reaction of each support. Draw the shear, moment, elastc curve and axial force…

A: Beam with UVL and point load is given. We need to calculate the reaction of each support and draw…

Q: 4. 1.25x104 m³ of runoff occurs from a 100-ha plot of uniformly sloping land in a certain half-hour…

A: Runoff (R) = 1.25 × 104 m3 Area of plot (A) = 100 ha Intensity of rainfall (I) = 10 cm/hr Duration…

Q: Two footings, one circular and the other square, are founded on the surface of a purely cohesionless…

A: Given data :-Two footings ,one circular and the other square are founded on the surface of a purely…

Q: A W610 x 82 beam of A 36 steel has end reaction of 302 kN and is supported on a plate with a length…

A: Yield Strength :Yield strength of an element is a maximum stress an element or component can bear…

Q: For a certain bridge project that is being evaluated, it was decided, at first, to use an I-section…

A: Given:Required:Static moment of inertia

Q: H Two sharp-ended pipes of diameter D1 = 50mm, and D2 = 100mm, each of length 100m, are connected in…

Q: 7.34 and 7.35 Use the virtual work method to determine the slope and deflection at point D of the…

Q: Explain the role of IoT in improving the efficiency of waste management processes in urban areas.

A: Explain the role of IoT in improving the efficiency of waste management processes in urban areas.

Q: Already answered in Bartleby. Do not copy the solutions. Please double check the solutions! Statics…

A: Given Load 200 lbAngle 30°Span 35 inDepth 25 inTo find out Moment about O

Q: (3) Determine the displacement of point B for the following tapered beam. (The Modulus of Elasticity…

A: A cantilever beam of length = 4mThe beam is loaded with a point load of 20 kN at its free end.The…

Q: The demand for electric power is usually much higher during the day than it is at night, and utility…

Q: A strata of clean, light-colored quartz sand located below the groundwater table has a moisture…

A: moisture content, w= 25.6%minimum void ratio, emin = 0.38maximum void ratio, emax = 1.109

Question

100%

A 5ft long bar with a 3in x 5in cross section is subjected to a 13,638lb tensile load. What is the tensile stress in ksi? Answer to two decimal places.
Type your answer...

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the tensile stress

VIEW

Step 2: Determine the tensile stress

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
W A 3ft long bar with a 1in x 1in cross section is subjected to a 14,153lb tensile load. What is the tensile stress in ksi? Answer to two decimal places. Type your answer...
A 5ft long bar with a 3in x 5in cross section is subjected to a 13,638lb tensile load. What is the tensile stress in ksi? Answer to two decimal places.
A 5ft long rod with a 0.63 inch diameter is subjected to a 10,661lb tensile load. What is the tensile stress in ksi? Answer to two decimal places.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the steel given that P= 96.3 kN? Express your answer in two decimal places.
} 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm?. If a tensile load was applied to an aluminum bar to achieve the same lateral (transvers) strain with the former (steel bar), what would be the load? Note: Original dimensions of the two bars are the same (Est = 2.1 x 105 MPa, Eat = 0.703 × 105 MPa, vg = 0.3, vat = 0.33) E = º , v = - Saterat Eaxial Fatuminum™ 3000 N A-500 mm² A=500 mm² Fatuminum=? 3000 N Steel Aluminum
Determine the value of modulus of elasticity having stress value equal to 50 MPa and strain equal to 0.04 I
A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of 11.6 * 106 psi. The rod is to be subjected to a torque T.What is the minimum required length L of the rod so that the cross section at one end can be rotated 60° with respect to the other end without exceeding an allowable shear stress of 45 * 103 psi?
2.) Answer the following: a.) a 22 ft long solid steel rod is subjected to a load of 15,000 lb. This load causes the rod to stretch 0.435 in. The modulus of elasticity of the steel is 30,000,000 psi. Determine the diameter of the rod. b.) A solid circular titanium control rod must support an axial tension force of 12,000 lb. Assume that the modulus of elasticity of the titanium in 16,500,000 psi. If the rod must elongate no further than 0.35 in. when the normal stress of the rod is 68,000 psi, determine the minimum rod diameter AND the maximum rod length.
In ASTM D245, what is the length of time for duration of load assumed for strength calculations? How does changing this duration affect the allowable stress?
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.