Each of the links AB and CD is made of steel (E = 29 x 106 psi) and has a uniform rectangular cros section of 1x1 in. Knowing that they support rigid member BCE. The downward load at point E is 10000 lbf. 8 in. 8 in. B O O A 10 in.- D -15 in. E What is the value of SE? (with the unit of in and get to the fourth decimal place)

Each of the links AB and CD is made of steel (E = 29 x 106 psi) and has a uniform rectangular cros section of 1x1 in. Knowing that they support rigid member BCE. The downward load at point E is 10000 lbf. 8 in. 8 in. B O O A 10 in.- D -15 in. E What is the value of SE? (with the unit of in and get to the fourth decimal place)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2: Determine the force in ALL the members of the truss. State if the members are in tension or compression. Show all your work to receive full credit. (Hint: It is not needed to find the reaction forces at C and E if you use the Method of Joints). Note: P1= 1000 lb and P: = 500 lb B C30 45 999 4 ft E 550 D. -4 ft- - 4 ft- 999 299
-5 @ 3m-15m- C F H J K ML boo I A 4@4m=16m B D G E 60 kips A For the truss shown, what is the force in member FG? B what is the force in member BE? + --D
1-45. The truss is made from three pin-connected members having the cross-sectional areas shown in the figure. Determine the average normal stress developed in each member when the truss is subjected to the load shown. State whether the stress is tensile or compressive. -0.6 in. AAC -3 ft- Auc= 0.8 in.2 AAB 1.5 in. 500 lb B
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
Physics The following truss is subjected to a load of P = 31 kN at joint C. The pin at joint A has a diameter of 25 mm and is subjected to double shear. Determine the average shear stress developed in pin A of the truss. Im PRN Im Pin A a. In your Hard Copy, draw a FBD of the truss. b. What is the Resultant force at A? Aresultant = Number Units (Answer to 3 sig digs) c. What is the shear stress in A? TA = Number Units (Answer to 3 sig digs
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in² for all the members. Determine the deformation sustained by members CG and FG. 12 kips 14 kips 16 kips A B с 10 kips |-6R-|-6A 8 ft ļE 5 ft ——6 ft—6 ft--6 ft-
8.10 This is steel, consisting of 9 rods that are articulated together in the nodes. There is a fixed bearing in A and a roller bearing in B. The steel is loaded with a point load, P, in the middle. The maximum permissible normal stress is oy = 200 MPa. Cross section: s9 S8 54 53 55 s1 S7 d = 40 mm S2 S6 1m 1m 1 m 1 m a) Calculate the rod forces. Express the answers with P, and state whether they are stretched or pressed. Is there any zero spells? b) Determine how large the load P can be without material breakage or buckling the spells. 3 m
Determine the force in member FG (assume FG is tension) of the truss shown in the figure below?. Set P = 671 lb. 2P 12h 12 12 12 Answer:
F ., É, are applied to the truss system. В a) Find member forces in each member and state if the members are in tension or 4 m compression. b) If the maximum force that any member can support is Tmax in tension and Cmax in compression, determine the maximum value of P that can be supported. A E 3 т 3 m 3 т 3 m F1 F2 F3 F4 F5 Tmax Cmax P 2P 40° 7 kN 8 kN 2P Note: Do not show zero forces in your calculations.
For the truss shown in Figure 2.3a, determine the force in member GH if m = 4 m, n = 7 m, a = 87°, andP = 4.5 kN. Indicate whether the member is in tension or compression. (Note: Use negative sign (-) if the member is in compression.) J m H Н т G m A В C D E P kN
Problem 1: The rigid bar ABC is supported by AD and BE. Determine: a. Inclination of member ABC after loading b. 8 at point E Members Properties: Member Materials Modulus Cross- sectional Area of Elasticity AD Aluminum 70GPA 450mm2 ВЕ Steel 200GPA 550mm2 E O •Im O:3m 45kN. t 0 4m