2.) Answer the following: a.) a 22 ft long solid steel rod is subjected to a load of 15,000 lb. This load causes the rod to stretch 0.435 in. The modulus of elasticity of the steel is 30,000,000 psi. Determine the diameter of the rod. b.) A solid circular titanium control rod must support an axial tension force of 12,000 lb. Assume that the modulus of elasticity of the titanium in 16,500,000 psi. If the rod must elongate no further than 0.35 in. when the normal stress of the rod is 68,000 psi, determine the minimum rod diameter AND the maximum rod length.

2.) Answer the following: a.) a 22 ft long solid steel rod is subjected to a load of 15,000 lb. This load causes the rod to stretch 0.435 in. The modulus of elasticity of the steel is 30,000,000 psi. Determine the diameter of the rod. b.) A solid circular titanium control rod must support an axial tension force of 12,000 lb. Assume that the modulus of elasticity of the titanium in 16,500,000 psi. If the rod must elongate no further than 0.35 in. when the normal stress of the rod is 68,000 psi, determine the minimum rod diameter AND the maximum rod length.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
Bar A was manufactured 2 mm less than bar B due to an error. The attachment of these bars to the rigid bar wouldcause a misfit of 2 mm. Calculate the initial stress in each assembly. Which of the two assembly configurationyou would recommend? Use modulus of elasticity of E = 80 GPa and diameter of the circular bars as 32 mm.
7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses in the two materials with an applied load of 45,000 lbs. 45,000 lbs 3.5"Ø 3.0"Ø Steel Aluminum
A threaded round steel bar is subjected to a tota axial pull of 8000 lb. If the diameter of the unthreaded portion is 7/8 in., the unit stress in that portion is A. 10,470 psi B. 13,310 psi C. 16,230 psi D. 19,880 psi
Calculate the steel ratio that will produce a tension-controlled failure if compressivestrength f’c = 28 MPa and steel yield strength fy the answer is 0.02167 but i don't know how to solve it please help
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
A round aluminum [E = 70000 MPa] rod must be designed for the following specifications: (a) The rod must be 2.09 m long. (b) The rod must carry a tensile load of 647 kN. (c) The normal stress in the rod must not exceed 150 MPa. (d) The rod must not elongate more than 5 mm. Determine the minimum diameter that can be used for the aluminum rod. Answer: Minimum diameter = i mm
A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of 11.6 * 106 psi. The rod is to be subjected to a torque T.What is the minimum required length L of the rod so that the cross section at one end can be rotated 60° with respect to the other end without exceeding an allowable shear stress of 45 * 103 psi?
An aluminium wire (E=10,600 ksi) having a diameter d=1/8 inch. and length L=14 ft is subjected to a tensile load P. If the maximum permissible elongation of the wire is 1/6 inch and the allowable stress in tension is 10 ksi, what is the allowable load Pmax? Answer in Ibs
A tension stress of 70 ksi was applied on a 12-in. long steel specimen. Determine the resultant elongation assuming that the deformation is entirely elastic. Assume a Young’s modulus of 30 * 106 psi.
A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, ofdiameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine:(i) the stress, (ii) the strain, (iii) the modulus of elasticity.(b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250 mm, bothmeasurements being made at 20~ The temperature of the spacer is then increased to 100~ the natural expansionbeing entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/~ determine:(i) the stress in the spacer, (ii) the compressive load on the spacer.rC.G.] [64 MN/m 2, 0.0008, 80 GN/m 2, 115.2 MN/m 2, 71 kN.] Could you please answer the parts after the first three? If you use * could you please explain what you mean by it! Thank You :)