Find the percentage of each phass developed at specificed temperature A327°C600300290Liquidliquidus500Solidus232°Ca +L400200185°C +L183°C18.361.9| 181°C 97.8155°C300Solus100a +B20080°CT80°C100204060100(РЫ)Composition (wt% Sn)(Sn)Temperature ("C)Temperature (F)

given; at temperature 1810c overall composition (wt % Sn) (W1)=80andat temperature 1850c overall…

A 327°C 600 300 290°C Liquid liquidus 500 Solidus 232°C F a +L 400 200 185°C +L 183°C 61.9 18.3 155°C | 181°C 97.8 300 Solvus 100 a +B 200 80°C I 80°C 100 20 40 60 100 (Pb) Composition (wt% Sn) (Sn) Temperature ("C) Temperature (F)

A 327°C 600 300 290°C Liquid liquidus 500 Solidus 232°C F a +L 400 200 185°C +L 183°C 61.9 18.3 155°C | 181°C 97.8 300 Solvus 100 a +B 200 80°C I 80°C 100 20 40 60 100 (Pb) Composition (wt% Sn) (Sn) Temperature ("C) Temperature (F)

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.74P: A manufacturer in the United States wants to sell a refrigeration system to a customer in Germany....

See similar textbooks

Similar questions

Solve correctly please. (Gpt/Ai wrong ans not allowed)
A 30 wt% Ni-70 wt% Cu alloy (Animated Figure 9.3a) is slowly cooled from 1400°C (2550°F) to 1150°C (2100°F). (a) At what temperature does the first solid phase form? i ! °C (b) What is the composition of this solid phase? i %wt Ni (c) At what temperature does the last of the liquid solidify? i °℃ (d) What is the composition of this last remaining liquid phase? i %wt Ni
100 2200 20 40 60 80 1200 2000 -Liquidus 1000 Liquid 1800 Solidus F a +L 1600 B+L 800 779°C (Tg). E 8.0 71.9 91.2 1400 (CaE (Cg) (CBE 1200 600 Solvus 1000 a + B 800 400 C 600 H 200 0 400 100 20 40 60 80 (Cu) Composition (wt% Ag) (Ag) 1- define pointe E? 2- define pointe B? 3- define the line AE? 4- define the line BG? 5- define the line FG? Temperature (°C) Temperature ('F)
None
Moving to another question will save this response. estion 46 What is the mass of a body in grams if it has a kinetic energy of 94.6N-m when moving at 2.25m/s? →→ Moving to another question will save this response. OLO L
= 14 15 16 17 18 19 20 21 22 23 24 25 26 A gas storage cylinder in an ordinary chemical laboratory measures 3.9 cm wide and 16. cm high. This is the label on it. olo Contents: N, gas Pressure: 7.93 atm If the cylinder is opened and the gas allowed to escape into a large empty plastic bag, what will be the final volume of nitrogen gas, including what's collected in the plastic bag and what's left over in the cylinder? Write your answer in liters. Round your answer to 2 significant digits. ?
Mechanical Engineering The fatigue strength limit Sn (n = 106) of a steel part is 112 MPa and its ultimate tensile strength (Sy) is 385MPa. Adopting Ct = 1, and S103 = 0.9 * Su* Ct, determine: (Use two decimal places in the answers), (* is multiplication signal): a) The fatigue strength (in MPa) corresponding to a life of 40000 cycles. b) The average life in cycles that this part would last if subjected to an alternating stress of 170 MPa due to bending.
1. Temperature (°C) From the diagram below, analyze a 40%Ni-60% Cu alloy at 1250°C. a.) What phases are present? b.) What are their chemical compositions? C.) If our system contains 100 grams, how much of each phase is present? 1300 MM CM 1200 20 -Liquid a Liquid. 112 3 4 5 ½ a 30 20 3 8 40 Composition (wt% Ni) 9 10 11 12 ½ 4 ½ 50
Please help for d. Both i) and ii) thanks
please show work and formulas so that i may learn the process correctly. if you use a table please mention which table was used. thank you so much. 2. Fill in the blank cells of this table: T( C) P(kPa) u(kJ/kg) Phase description 175 2524.5 325 4000 325 Saturated liquid
A pipe 40 cm in diameter contains steam at 100°C and is covered with asbestos (K = 0.0006 cal/cm*deg*sec) 10 cm thick. The outside temperature is kept at 60°C. How much should the thickness be increased in order that the rate of heat loss will be decreased by 25%? (A) 14.34 cm B) 4.34 cm 34.14 cm D) 24.43 cm
e IY: %VY OLD ? د ميکانيك شهري 2021.pdf UNIVERSITY OF BASRAH - COLLEGE OF ENGINEERING DEPARTMENT OF CIVIL ENGINEERING Subject: Engineering Mechanics-Static Class: 1st year, 1st term Exam. : Semester Date: 16/3/2021 Examiner: Dr. Mazin, Dr. Aqeel, Dr.Ahid and Dr.Jaffar Time: 1.5Hours Q1] (10 Marks) A- In Fig.A , If the resultant force acting on the bracket is to be 642 N directed along the positive x axis, determine the magnitude of F. B- In Fig.B , Determine the magnitude of the resultant force acting on the screw eye and its direction measured clockwise from the x axis. C- In Fig.C , Resolve the 100N force into components along the u and v axes, and determine the magnitude of each of these components. D- In Fig.D, Determine the moment of the force about point O. 300 N 60N 25° 32 45° 60° 505 N 50° 40N Fig. A 50 N Fig. B 400 N 100N 28° 18 2.12 m Fig. C 2.12 m Fig.D Q2] (10 Marks) A- In Fig.A , Replace the loading system by an equivalent resultant force and specify where the resultant's…