A 140-lb bucket is suspended from a cable on the wooden frame. Determine the magnitude of the resultant internal normal force (ND) on the cross section at D Note that A and B are both pin connections. Express your answer in lbs rounded to 3 significant digits. 1 ft 1 ft I B 2 ft 30° 1 ft 3 ft G E A 2 ft- 9 DH C

A 140-lb bucket is suspended from a cable on the wooden frame. Determine the magnitude of the resultant internal normal force (ND) on the cross section at D Note that A and B are both pin connections. Express your answer in lbs rounded to 3 significant digits. 1 ft 1 ft I B 2 ft 30° 1 ft 3 ft G E A 2 ft- 9 DH C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.76P: The 50-ft measuring tape weighs 2.4 lb. Compute the span L of the tape to four significant figures.

See similar textbooks

Similar questions

Determine the magnitude of the vertical support reaction at Point A. Enter your number to TWO decimal places, If an integer, just enter the integer number. Remember, the appropriate unit! (If applicable, use a "-" to indicate multiply in the unit.) A - 6m- 0.5 kN/m -3 m- 3 kN 5 kN•m
A series of compound levers is used as weighbridge. If a mass of 14.4kg is placed on the pan P and it is required that x = 475mm to balance the beam ABC, determine the mass (in 1 decimal digit of a kg) of the truck. There are pins at all points lettered. Take EF - 0. 2m, FD = 3m, KG = GH = 7m, and HI = KJ - 0.2m. 2nd question (answer in Bonus problem e): Is it necessary for the truck to be symmetrically placed on the scale? Explain. JKG & GHI are INDEPENDENT of EACH OTHER.
Determine the extension (m) of the whole system shown if k1 = 14.7 N/m, k2 = 21.23 N/m, k3 = 38.22 N/m, k4 = 48.78 N/m, and k5 = 52.73 N/m and a force of 62.11 N is applied. (Use 2 decimal places for the final answer.)
F1 2m F2 A 3.2m 1.8m AF, = 153 N load and a F, = 99 N are applied to the frame which is supported by pins at A and B. These loads are applied perpendicular to the beams. The two beams AC and BC make a right triangle. You may neglect the weight of the members. Find the magnitude of the force at pin C. For this problem, use the coordinate frame given. 1.5 m 4------ 1.5 m +----- 2.4m
The body on the 15-degree incline is acted upon by force P inclined at 20 degrees with the horizontal. If P is resolved into components parallel and perpedicular to the incline and the value of the parallel component is 41 Ibs, compute for the value of the perperdicular component, Pper. Pper 200 par 15° .
5. The cable supports the three loads shown. Determine the magnitude of Pi if P2 = 600 N and yB = 3 m. Also find sag yD E 1 m A YD Ув 4 m B D P2 P2 P1 6 m 6 m 3 m -3 m
2 m 2 m 2 m 2 m D F G H 2 m 1 m C 0.5 m 2 m F B M 2 m Determine the forces in members DE and DL. State if each forces are compression or tension. If the force is 10 kN. Input DE force member and four decimal values on the blank indicate the stress (Tension or Compression.) e.g: 829.91 N-T
For force P with magnitude 18.5 kN, find the magnitude of the force in member AC. Give your answer in kN (kilonewtons). P 13 12 3 m B C 4m -3 m D 4 m IVE ototo 3 m F
Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member GF if X=651N, Y=232N, Z=134, a=5.7m and b=3.2m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Determine the internal resisting forces and mo- ment transmitted by section aa in the bracket shown in Fig. 125 mm -375 mm 60° B 250 mm 300 N 30°
The lifting arm shown below needs to lift a weight of 4 (N). Assuming the links are weightless, determine the magnitude of the force being applied by the pin at B on the lifting arm to the nearest hundredth of a newton. 10Em) 6icm- 150 A Servo Horn Arm 4 (W) 'Servo
The device shown is designed to apply pressure when bonding laminate to each side of a countertop near an edge. If a 120-N force is applied to the handle, determine the force which each roller exerts on its corresponding surface. C 165 mm- 30 mm 120 N 45 30 mm 45 mm T