Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the maximum allowable torque Tmax that may induced on the wrench if the allowable shear stress is 60000 KPa? Also, determine shaft twist angle (in degrees) under the impact of the maximum torque? (Neglect the bending effect and take the modulus of rigidity as 78 GPa) .

Solid steel wrench (shown in Fig. 4) has a radius of 0.4 cm. and a length of 0.2 m. What is the maximum allowable torque Tmax that may induced on the wrench if the allowable shear stress is 60000 KPa? Also, determine shaft twist angle (in degrees) under the impact of the maximum torque? (Neglect the bending effect and take the modulus of rigidity as 78 GPa) .

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.19P: A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the...

See similar textbooks

Similar questions

A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
The hollow rod shown below is 2.99 meters long and is subjected to a torque of 988 Nm at end B. The diameter of the rod is 30 mm and has a wall thickness of 5 mm. The shear modulus of the material is 80 GPa, calculate the angle of twist in radians at B. TNm B meters
EHide blocks Lets consider a solid circuiar shalt subjected to the torque loads as shown. Determine the minimum required diameter "Dif the shaft is made of a material having a shear modulus G 50 GPa, so that the maximum angle of twist at its end will not exceed -0.35° (calculated according to the positive sign convention). 100 N.m 500 N.m 200 N.m 300 mm 600 mm 600 mm Select one: O 40 mm O 70 mm O 80 mm O 60 mm O 50 mm
2. Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque ofT 171N.m the missing Torque 171(T).
A steel shaft is transmitting 55 hp at 1200 rpm. The nature of the load and the type of service of the shaft is such that the allowance shearing stress based on the pure tension is 4000 psi. (MAXIMUM TORSIONAL STRESS AND ANGLE OF TWIST FOR A SOLID SHAFT) Calculate the diameter of the shaft to the nearest commercial size of the shafting. 2.Calculate the torsional deflection of the shaft in degree for one foot length of the shaft.
Two designs for shaft are being considered. Both have an outside diameter of 60 mm and are 500 mm long. One is solid but the other is hallow with an inside diameter of 40 mm, both are made from steel ( G=80 GPa). Compare the torsional shear stress, and the mass of the two designs if they are subjected to a torque of 71 N.m.
PLEASE ANSWER ASAP TY! The shaft shown has a diameter of 30 mm and is fixed at points A and B. Shear Modulus = 75 GPa. a) What is the internal torque in segment AC (in N-m)? b) Determine the maximum torsional shear stress experienced at segment AC (in MPa). c) What is the torsional shear stress at the center of the cross-section of the shaft (in MPa)? d) Determine the reactive torque at point B (in N-m).