7. Design a muff coupling for joining shafts transmitting 8 kW at 400 rpm. The shaft and the key are made of steel with 45 MPa and 80 MPa allowable stresses in shear and crushing, respectively. The material of the sleeve is CI, with allowable shear stress 10 MPa. Service factor KS =1.2.

7. Design a muff coupling for joining shafts transmitting 8 kW at 400 rpm. The shaft and the key are made of steel with 45 MPa and 80 MPa allowable stresses in shear and crushing, respectively. The material of the sleeve is CI, with allowable shear stress 10 MPa. Service factor KS =1.2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
PROBLEM: A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in diameter and 92 mm hub length. Six 16-mm bolts in a 165-mm diameter bolts circle connect the flanges. The keyway is 6 mm shorter than the hub length and the key is 14 mm x 14 mm. Coupling is to transmit 45 kW at 160 rpm. For all parts, yield point value in shear is one-half the yield point value in tension or compression that is 448 MPa. Find a) the shearing stress of key and its factor of safety; b) the bearing stress of key and the factor of safety based on yield point; c) the shearing stress in bolts and factor of safety based on yield point. (Board problem, November 1983) 14 mm x 14 mm x 86 mm d = 16 mm Dr = 111 mm D= 57 mm Dp = 165 mm w = 50 mm 92 mm Dimensions in mm
8. Design a clamp coupling for transmitting 25 kW at 300 rpm. Allowable shear stresses in shaft and key are 50 MPa and 45 MPa, respectively. The number of bolts joining the two halves of muff is 4. The permissible tensile stress in the bolt is 70 MPa and the permissible crushing stress in the key is 90 MPa. The coeffi cient of friction between the muff of the CI and the shaft of steel is 0.20.
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2 . The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
A mild steel shaft has to transmit 75 kW at 200 rpm. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the shaft and keys 40 N/mm²Shear stress for bolts = 28 N/mm²Shear stress for C.I. coupling = 20 N/mm² Take wearing stress as twice the shear stress value and number of bolts for coupling as 6.
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Design a compression coupling for a shaft to transmit 1300 N-m. The allowable shear stress for the shaft and key is 40 MPa and the number of bolts connecting the two halves are 4. The permissible tensile stress for the bolt material is 70 MPa. The coefficient of friction between the muff and the shaft surface may be taken as 0.3.
Design a flanged coupling that will be able to carry power of 1,500 HP using a factor of safety of 3.3 at 630 rpm. The shaft diameters of the equipment the coupling will connect are both 5 inches. Check your design for the following stresses if N = 3.3 is satisfied: 1. Bolt shearing; 2. Bolt bearing; 3. Shearing of hub from coupling flange; 4. Shear on key; 5. Compression on key; Select dimensions whichever is higher. 6. Calculate also minimum length of engagement of the bolt and nut if these are of the same material. 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only Instructions:
A flange coupling is to connect two 57 mm shafts. The hubs of the coupling are each 111 mm in diameter and 92mm thick and the flange web are 19 mm thick. Six 16 mm bolts in a 165 mm diameter circle connect the flange.The keyway is 6 mm shorter than the hub’s thickness and key is 14 mm x 14 mm. Coupling is to transmit 45 KW at160 rpm. For all parts, yield point value in shear is one – half the yield value which is 448 MPa. Calculate the forceon the shaft