6.2. Consider a common telephone channel with the bandwidth limited from 300 Hz to 3400 Hz modeled by an ideal band pass filter (zero attenuation between 300 and 3400 Hz, complete rejection of signals outside the 300 - 3400 Hz range). You apply a square wave of 400 Hz, 1 Vpp amplitude, 50% duty cycle to the input. 6.2.1. How would the signal waveform look like at the output of this channel (time domain)? Draw an approximate sketch! 6.2.2. How would the spectrum of the signal at the output of this channel look like? Sketch!

6.2. Consider a common telephone channel with the bandwidth limited from 300 Hz to 3400 Hz modeled by an ideal band pass filter (zero attenuation between 300 and 3400 Hz, complete rejection of signals outside the 300 - 3400 Hz range). You apply a square wave of 400 Hz, 1 Vpp amplitude, 50% duty cycle to the input. 6.2.1. How would the signal waveform look like at the output of this channel (time domain)? Draw an approximate sketch! 6.2.2. How would the spectrum of the signal at the output of this channel look like? Sketch!

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

then second questrion po eh eto 2. Determine the over-all transmittance of the signal flow graph shown below.
Q2. For the scheme shown in Figure Q2, i. Draw the spectrum of the baseband signal (multiplexer output) for the multiplexer. ii. Determine the bandwidth of the baseband signal (multiplexer output) for the multiplexer. i. Determine the minimum transmission bandwidth of the multiplexer. Explain, briefly, the modification needed for the multiplexer in the figure to achieve this bandwidth. 4 kHz cos 10,000xt Basebund signal cos 24,000mt cos 2000mt cos 32,000nt Figure Q2
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
In an Amplitude Modulator where the carrier and modulating signals are both sine waves, the frequency spectrum of the resulting AM signal is shown below. 12V 2V 2V kHz 803 808.6 a) Determine the equation of the modulating signal b) Calculate the bandwidth of the AM signal c) Calculate the effective current of the AM signal thru a 75-ohm load. d) Sketch the AM wave and label the maximum and minimum voltage of the signal.
This is a practice question from Electronics Engineering, double sideband supressed carrier problem.
One input to a conventional AM modulator is a 600 kHz carrier with amplitude of 22 V. The second input is a 20 kHz modulating signal that is of sufficient amplitude to cause a change in the output wave of +9 V. Determine: a. Upper and lower side frequencies. b. Percent modulation. c. Peak amplitude of the modulated carrier and the upper and lower side frequency voltages. d. Maximum and minimum amplitudes of the envelope. e. Expression for the modulated wave. Then, f. Draw the output spectrum. g. Sketch the output envelope.
I need proper solution for the following( underdstandable writing and well explained) thank you What is resonance in LCR circuit? and tell the difference between impedance and resistance?
In three-level PWM, the modulating process operates on each portion of the modulating function separately. The output peak value is still given by the depth of modulation, but the RMS value of the square wave is not Vin. Compute the THD for three-level PWM as a function of the depth of modulation (modulation index k).
Discuss how the circuit produces a Frequency Modulated Signal
With the aid of diagrams, show and explain how phase locking is used to demodulate a frequency-modulated (FM) signal.
i)Modulation process takes place in the modulator with two injection signals namely data orinformation and carrier. It is a vital step in generating a decent signal for electronic communication.Whenever the carrier is modulated by the information signal, new signals at different frequenciesare generated as part of the process. These new frequencies occur in the frequency spectrum withinthe range of the carrier frequency. Conclude these frequencies and mathematically explain itsgeneration with the help of diagrams. A) Upper sideband and lower broadbandB) Lower sidefloor and upperside floorC) Lower peak and upper peakD) Upper sideband and lower sidebandE) Lower bandwidth and upper gainF) All of the aboveG) None of the above
The figure shows multiple modulation schemes for the signal that is given by the dashed line sinusoidal function, the X-axis is the time axis is seconds and the Y-axis is the amplitude. Answer the following: What is the quantization noise in a modulator that uses a 4-bits register for the analog to digital conversion of the given sinusoidal signal? Please give deatiled solution for good understanding