6. It has been determined experimentally that steel wires of a certain length have strength with a mean value of 1 kip and a coefficient of variation of 16%. What is the probability that the strength of such a wire is less than 0.7 kips? Try Type I and Type III asymptotic distributions of extremes and compare the results. Given: „k x' : = e* 'k! k=0 IM

6. It has been determined experimentally that steel wires of a certain length have strength with a mean value of 1 kip and a coefficient of variation of 16%. What is the probability that the strength of such a wire is less than 0.7 kips? Try Type I and Type III asymptotic distributions of extremes and compare the results. Given: „k x' : = e* 'k! k=0 IM

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the second experiment a beam is simply supported at its two ends then loaded in the middle as seen in Figure 2 below. A dial gauge is used to measure the deflection at the middle, while a gauge on each end is used to measure the inclination of the beam at the supports (to compare to theoretical values). (b) * x2 Pin Support P Roller Support Figure 2: Simply Supported Beam 1. What are the constraints in this experiment? X2
I need an answer ASAP, please answer all demands.
Solids
A student wants to measure the strain at a particular point K on a loaded specimen, so she affixes a 45° strain rosette at point K and obtains the following results: €A = 390 μrad EB = 275 μrad Ec = 325 prad After packing up and going home to analyse her results, she realises that the strain rosette was misaligned by 0 degrees CW (where a negative corresponds to CCW) from the x-y axes-ie. Gauge C is not parallel with the x-axis and is instead parallel with a different x' axis that is rotated by 0 degrees-where: 0 = 16 deg Instead of replacing the rosette and retaking measurements, the student realises she can use what she learned in ENGG2400 to find the strains she's interested in. b 45° 45° a) Draw a diagram of the situation, showing both the x-y axes and the strain rosette. b) Calculate Exx, Eyy and Yxy. c) Calculate the maximum in-plane shear strain and the associated average normal strain. I X
Q 05 A metallic rod of 500mm length and 50mm diameter, when subjected to a tensile force of 100KN at the ends, experiences an increase in its length by 0.5mm and a reduction in its diameter by 0.015mm. The Poisson's ratio of the rod material is
5
The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Submit Correct Part B My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m
4. Two exactly similar wires, one of steel and the other of copper, are stretched by equal force. If the total elongation is 2 cm, find how much is each wire elongated. Y for steel is 2 x 10 N/m² and for copper is 12 x 10 N/m.
A rigid bar is supported by two copper ro ds and the gap (A) between the aluminu m rod and the bar is 1.50 mm. If the temp erature for all materials is increased by 4 0 degrees Celsius, will the aluminum rod touch the rigid bar or not? Prove your ans wer by stating computed data. Disregard the weight of the rigid bar. For each copper bar, A = 500 mm^2, E = 120 GPa, and a = 1 6.8 μm/(m. C). For the aluminum bar, A = 400 mm^2, E = 70 GPa, and a = 23. 1 μm/(m. C).(* Copper Aluminum Copper 750 mm
A 1-m long steel bar (E = 200 GPa) of 10 x 10mm dimension fixed at both ends is heated by 90°C from initially 30°C. What is the normal stress, in MPa, induced in the system due to change in temperature? Use a = 12 x 10-6 per °C. Encode you answer in whole number. Round your answer to 0 decimal places. Add your answer