A high-strength bolt that is passing through a steel plate is subjected to a tension force of P=4.6 kN as shown in the figure. The hole in the metal plate has a diameter of D=14 mm which is bit larger than the diameter of the bolt (d, = 12 mm) to allow for easy installation process. The plate has a thickness of t= 11 mm. The bolt head has a thickness of a = 3 mm and an outer diameter of dh = 19 mm. Determine the bearing stress between the bolt head and the steel plate. A) 22 MPa B) 25 MPa C) 29 MPa D) 30.5 MPa E) 35 MPа VP

A high-strength bolt that is passing through a steel plate is subjected to a tension force of P=4.6 kN as shown in the figure. The hole in the metal plate has a diameter of D=14 mm which is bit larger than the diameter of the bolt (d, = 12 mm) to allow for easy installation process. The plate has a thickness of t= 11 mm. The bolt head has a thickness of a = 3 mm and an outer diameter of dh = 19 mm. Determine the bearing stress between the bolt head and the steel plate. A) 22 MPa B) 25 MPa C) 29 MPa D) 30.5 MPa E) 35 MPа VP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 94 GPa] with a cross-sectional area of A₁ = 280 mm2. Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A2 = 590 mm². All bars are unstressed before the load P is applied; however, there is a 3-mm clearance in the pin connection at A. Assume L₁ = 1840 mm, a = 880 mm, b = 540 mm, c = 430 mm, and L₂ = 1340 mm. If a load of P = 87 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar. h (1) L₁ b a BI Answers: C (2) D L2
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress (in Mpa) in the bronze given that P= 188 kN? Express your answer in four decimal places.
Find the value of p
Determine the following: Displacement of B (in mm) with respect to A. Displacement of C (in mm) with respect to A. Principal stresses at point O, if it is 200mm from C. (unit should be kPa). A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
A fillet-welded joint is shown in the figure. The size of the weld is 8 mm. Safe stress in the weld is 110 N/mm². What is the safe force (to the nearest magnitude) to which the weld can be subjected? 80 mm 60 mm
For this problem, I decided to start out by solving the junction E because that is where ht external forces are applied but this tends to result in 3 unknown values and only to equations to solve. I am pretty sure there is a zero force member somwhere in there that makes this all workout but I don't know how to identify it, how do I do this.
An aluminum alloy bar (E = 72 GPa) has length L = 2m, constant thickness t = 20mm, and a rectangular cross section whose width varies linearly between b2 = 115 mm at the fixed support to b1 = 100mm at the free end. Assume that the taper of the bar is small. If P2 = 200kN, hwta is P1 so that the displacement tc=0. What is the displacement tb?
Please answer in detailed solution and explain step by step
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m by applying a pure moment 'M'. If E is 200 GPa, then magnitude of the pure moment 'M' will be
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9