Figure below shows a rod that supports a mechanism for food manufacturing company. Given that the following values on the table would be observed on the system, determine the value of normal stress in MPA, round off your answers to nearest whole number. Ørod 7 mm B P P 2450 N 130 mm d a b 195 mm (1) 150 mm d 90 mm 60% D

Figure below shows a rod that supports a mechanism for food manufacturing company. Given that the following values on the table would be observed on the system, determine the value of normal stress in MPA, round off your answers to nearest whole number. Ørod 7 mm B P P 2450 N 130 mm d a b 195 mm (1) 150 mm d 90 mm 60% D

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter7: Length And Length-related Variables In Engineering

Section: Chapter Questions

Problem 43P: A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the...

See similar textbooks

Similar questions

Figure below shows a rod that supports a mechanism for food manufacturing company. Given that the following values on the table would be observed on the system, determine the value of normal stress in MPA, round off your answers to nearest whole number. Ørod 6.5 mm P 2250 N a 125 mm 200 mm 165 mm (1) C d. 85 mm 60%
Q5) A specimen of alloy having a rectangular cross section of dimensions 5 mm x 16 mm is deformed in tension. Using the Load (N) Length (mm) tabulated data to plot the engineering stress – strain curve and 75.000 4669.56 75.03 then calculate the following: 8985.96 75.08 12694.14 75.09 (a) Modulus of elasticity. 16264.98 75.14 17991.54 75.18 (b) The yield strength. 19816.2 75.26 22484.52 75.421 (c) The modulus of resilience. 24623.1 75.621 26369.28 75.846 28292.04 77.68
Figure shows a homogeneous, rigid block weighing 55 kN that is supported by three symmetrically placed rods. The lower ends of the rods were at the same level before the block was attached.. Use the following dataDetermine the stress in each rod after the block is attached and the temperature of all bars increases by 30⁰C
Computation must be completeAnswer in two decimal places.Box your final answer
Problem 8: Inputs: ● FA = 125 lb FB = 75 lb Fc= 87 lb r = 3 in (radius to all load cells) FA X FC A 300 Z 0 FB B A circular plate is used in a machine called a compactor to determine the mechanical properties of various materials. In this particular test, three load cells are located at the same radial distance from point O. (Load cells measure force). If the load cells measure the forces shown above, determine the equivalent force system of a single force acting on the plate. Specifically: a) What is the x-coordinate of the point where the resultant force's line of action intersects the x-y plane? You must include sign, positive or negative. 30° b) What is the y-coordinate of the point where the resultant force's line of action intersects the x-y plane? You must include sign, positive or negative. y
Please examine and provide solution
1-A thin aluminum plate profile shown in the accompanying figure is subjected to an axial load. deflection and the average normal stresses along the plate using the model shown in the figure. The plate has a thickness of 0.5 cm and a modulus of Approximate the 2 cm 2 cm elasticity E=70 GPa 2 cm 2 сm 3000 N б ст 6 cm 10 cm 2 cm 2 cm
Two masses are attached to a uniform meter stick as shown in the figure below. Themasses of m1 and m2 are as given and the meter stick weighs 150 g. A force F withunknown magnitude is applied on one end of the stick at an angle of 30° to balancethe system. (a) What is the magnitude of F? (Ans: 6.21 N)(b) What are the reaction forces on the support? (Ans: Rx = 5.38 N; Ry = 5.80 N)
Show complete solutions with FDB Subject: Mechanics of Deformable bodies
Also find the y component of the reaction exerted on the bar by the support at A? (Ay=?)
Two couples act on the beam. (Figure 1) Figure 60° 0.2 m A 30° 1m 300 N 2 m 1 of 1 500 N Part A If the resultant couple is to be zero, determine the magnitude of P. Express your answer to three significant figures and include the appropriate units. P = Submit Part B F = Submit O μA Value 0 Request Answer If the resultant couple is to be zero, determine the magnitude of F. Express your answer to three significant figures and include the appropriate units. O μÀ Value Units Request Answer X Units ? X ?
A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is applied the block deforms into the shape shown by the dashed line. (Figure 1) Part A Determine the magnitude of P. The block's material has a modulus of rigidity of G= 24 GPa .Assume that the material does not yield and use sma angle analysis. Express your answer to three significant figures and include the appropriate units. Figure µA ? Value kN P = 150 mm- You have already submitted this answer. Enter a new answer. No credit lost. Try again. 0.5 mm -- Submit Previous Answers Request Answer 150 mm Provide Feedback Next >