3.13 The torques T and 2T are carried by a shaft consisting of steel and aluminum segments. If the working shear stresses are 14 000 psi for steel and 7500 psi for aluminum, and the angle of rotation at the free end must not exceed 8, find the largest allowable value of T. For steel, use G = 12 x10^6 psi, and for aluminum, use G = 4 x10^6psi. Aluminum 2 ft 3 ft 1.5 in.- 27 Steel 2 in.

3.13 The torques T and 2T are carried by a shaft consisting of steel and aluminum segments. If the working shear stresses are 14 000 psi for steel and 7500 psi for aluminum, and the angle of rotation at the free end must not exceed 8, find the largest allowable value of T. For steel, use G = 12 x10^6 psi, and for aluminum, use G = 4 x10^6psi. Aluminum 2 ft 3 ft 1.5 in.- 27 Steel 2 in.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of monel metal is subjected to five torques acting in the directions shown in the figure. The magnitudes of the torques are T1= 1000 lb-in., T2= T4= 500 lb-in., and T3= T5= 800 lb-in. The tube has an outside diameter of d2= 1.0 in. The allowable shear stress is 12,000 psi and the allowable rate of twist is 2.0°/ft. Determine the maximum permissible inside diameter d1, of the tube.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
3.22 The compound shaft, composed of steel, aluminum, and bronze segments, carries the two torques shown in the figure. If Tc = 250 lb- ft, determine the max- imum shear stress developed in each material. The moduli of rigidity for steel, alu- minum, and bronze are 12 × 10° psi, 4 × 10° psi, and 6 × 10° psi, respectively. %3D 500 lb · ft | Steel 1.0 in. Aluminum | 2 in. Bronze $1.0 in. B D C 6 ft →le 4 ft →l– 3 ft –
A hollow steel shaft is stressed to 55 MPa by a torque of 100,000 ft-lb. If the inside diameter is 2/3 of the outside diameter and if G = 83 GPa, find the angle of twist in degrees if the shaft is 5 meters long.
1. A solid circular shaft transmits 75 kW power at 200 rpm. Calculate the diameter of the shaft and the maximum shear stress acting on it, if the twist in the shaft is not exceeding 1° in 2 m length of the shaft. Take modulus of rigidity as 102 GPa.
The shaft in Fig. (a) consists of a 3-in. -diameter aluminum segment that is rigidly joined to a 2-in. -diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the maximum shear stress developed in each segment when the torque T = 10 kip in. is applied. Use G = 4×106 psi for aluminum and G = 12×106 psifor steel
1.A hollow steel shaft transmits 600 kW at 500 r.p.m. The maximum shear stress is 62.4 MPa. Find the outside and inside diameter of the shaft, if the outer diameter is twice of inside diameter, assuming that the maximum torque is 20% greater than the mean torque. 2. A motor car shaft consists of a steel tube 30 mm internal diameter and 4 mm thick. The engine develops 10 kW at 2000 r.p.m. Find the maximum shear stress in the tube when the power is transmitted through a 4 : 1 gearing. 3.A line shaft rotating at 200 r.p.m. is to transmit 20 kW. The allowable shear stress for the material ofthe shaft is 42 MPa. If the shaft carries a central load of 900 N and is simply supported between bearing 3 metre apart, determine the diameter of the shaft. The maximum tensile or compressive stress is not to exceed 56 MPa. 4.A cast gear wheel is driven by a pinion and transmits 100 kW at 375 r.p.m. The gear has 200 machine cut teeth having 20° pressure angle and is mounted at the centre of a 0.4 m…
A shaft consisting of an aluminum segment and a steel segment is acted upon by two torques. The shaft is attached to the wall at point C. The diameter of the aluminum segment is 0.062 m and the diameter of the steel section is 0.034 m. The shear elastic modulus for aluminum is G = 28 GPa and the shear elastic modulus for steel is G = 83 GPa. Calculate the angle of twist at point A if the value of T = 699 N m. Multiply your final answer by 104 and submit that as your input with four significant figures after the decimal point. For example, if your final answer is 0.00005555 then input 0.5555. Aluminum 900 mm 2T B HH Steel 600 mm T A
A steel shaft 'A' of diameter 'd' and length 'l' is subjected to a torque T Another shaft 'B' made of aluminium of the same diameter 'd' and length 0.51 is also subjected to the same torque "T'. The shear modulus of steel is 2.5 times the shear modulus of aluminium. The shear stress in the steel shaft is 100 MPa. The shear stress in the aluminium shaft, in MPa, is: (b) 50 (a) 40 (c) 100 (d) 250
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is ___KN-m 3.82 2.64 0.48 1.18 5.03
3.12 The solid compound shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear m oduli are 28 GPa for alu- minum, 83 GPa for steel, and 35 GPa for bronze. 4 kN m Steel 1.5 kN m Aluminum Bronze 100 mm 75 mm -3 m- 15m- 2m- FIG. P3.12
Cross Section Shown Is 6 Ft Long And Has A Wall Thickness Of 0.12... A steel tube with the cross section shown is 6 ft long and has a wall thickness of 0.12 in. Determine: (a) If the allowable shear stress is 8000 psi, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 12 x 10^6 psi for steel. Figure: 2 in. 2 in. e 2 in.-2 in. –