1. A shaft system ABC consists of a solid bar AB welded to a hollow bar BC. The shaft is subjected to the torque system as shown in Figure Q1. Determine the maximum torque, T that can be applied if the allowable shear stress is 40 MPa and the allowable total angle of twist at point C is 0.035 rad. Modulus of rigidity, G is 80 GPa. 3/8 2 m Im 27 80 mm T 60 mm 90 mm A B C Figure Q1 [Ans: T= 2010 N.m]

1. A shaft system ABC consists of a solid bar AB welded to a hollow bar BC. The shaft is subjected to the torque system as shown in Figure Q1. Determine the maximum torque, T that can be applied if the allowable shear stress is 40 MPa and the allowable total angle of twist at point C is 0.035 rad. Modulus of rigidity, G is 80 GPa. 3/8 2 m Im 27 80 mm T 60 mm 90 mm A B C Figure Q1 [Ans: T= 2010 N.m]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
Determine the resisting torque at support A and B , of the shaft shown in the figure.
A solid steel shaft must not twist through more than 3° in a 6-m length whensubjected to a torque of 12 kN • m. (a) Find the diameter of the smallest shaft that can be used. (b) What is the maximum shear stress in the shaft of this diameter? Use G = 83 GPa for steel.
Vi
The A36 steel shafts as shown in the figure below are made from two segments: solid segment AC with diameter = 1 in and a hollow segment CB with an outside diameter = 2 in and inside diameter = 1 in. The shaft is fixed at both ends. Determine the magnitude of the applied torque T (lb-in) if the reaction at A is 600 lb-in clockwise.
The axis ABCD receives a torque of 500Nm from the motor and transmits movement to other devices, by means of belts and pulleys connected at B and C. If it is known that the torques exerted on pulleys B and C are as shown In the figure, determine the minimum radius the shaft must have. You should consider that at point D of the motor there is a bearing that acts as a support for the shaft as at point A. The material of the shaft and its allowable shear stress are indicated in the drawing.Determine:to. Free-Body diagram.b. Shear force diagrams.c. Bending moment diagrams.d. Identification of the critical point of the axis.e. Calculation of the axis radius. tperm=80MPa
Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T0 = 10 kN.m is applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm.
The hollow rod shown below is 2.99 meters long and is subjected to a torque of 988 Nm at end B. The diameter of the rod is 30 mm and has a wall thickness of 5 mm. The shear modulus of the material is 80 GPa, calculate the angle of twist in radians at B. TNm B meters
TORSION An aluminum shaft with a constant diameter of 70 mm is loaded by torques applied to gears attached to it. Use G = 28 GPa. DETERMINE: A. the relative angle of twist of gear D relative to gear A (in degrees) B. the direction of the rotation of A relative to D? PROVIDE FBD
A steel 0.75-in diameter shaft (G= 12,000 ksi) is subjected to the following torques in lb-ft: TA = 50; TB = 70; TC = 30; TD = 10. The directions of the applied torques are indicated in the figure. The bearings shown allow the shaft to turn freely. The length of each segment is equal to 38 in. (a) Plot a torque diagram showing the internal torque in segments (1), (2) and (3) of the shaft. Show the FBD of each segment using a double-headed arrow to represent each torgue. Use the same rule of signs as in the lecture. Determine (b) the maximum shear stress magnitude (ksi) in the shaft. (c) the rotation angle, in degrees, of pulley D with respect to pulley B. Note: Follow the rule of signs with FBD in each sections. Show complete step by step solution and proper FBD. Solid shaft: J = (₶/32 )( D4) Hollow: J = (₶/32)(D4 - d4)
As the electric motor rotates at a constant speed, a torque of 500nm is applied to the ABCD shaft. When G = 27 GPa and the torques shown in the figure are applied to the B and C pulleys, what is B and C torsion.
The steel shaft is made from two segments: AC has a diameter of 0.5 in., and CB has a diameter of 1 in. The shaft is fixed at its ends A and B and subjected to a torque of 500 lb-ft. Gst = 10.8(10³) ksi. (Figure 1) Figure sin. A 0.5 in. Jc 8 in D 500 lb-ft 12 in. 1 in. B < 1 of 1 Part A Determine the maximum shear stress in the shaft Express your answer to three significant figures and include the appropriate units. Tmax= Submit Provide Feedback μÅ Value 6 Request Answer Units www. ?