3. Reservoir A and B have elevation of 100 m and 160 m respectively. A pump is installed near reservoir A to pump the water from A to B. The rate of flow in the pipes is 700 L/s and the pipe has length of 1100 m with a diameter of 600 mm. Compute the added energy produce by the pump if A) f = 0.022 B) n = 0.015 C) C = 120 El 100 600mm El 160

3. Reservoir A and B have elevation of 100 m and 160 m respectively. A pump is installed near reservoir A to pump the water from A to B. The rate of flow in the pipes is 700 L/s and the pipe has length of 1100 m with a diameter of 600 mm. Compute the added energy produce by the pump if A) f = 0.022 B) n = 0.015 C) C = 120 El 100 600mm El 160

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

E the rate of 150 litres per capita per day from a river 2000 m away. The difference in elevation between the lowest water level in, the sump and the reservoir is 36 m. If the demand has to be supplied in 8 hours, determine the size of the main and the brake horse power of the pumps required. Assume maximum demand as 1.5 times the average demand. Assume f 0.0075, velocity in the pipe 2.4 m/sec, and efficiency of pump 80 per cent. u. Water has to be supplied to a town with one lakh population ot %3D 1960)
9:46 M回 O NI l l 96%l IMG 20220311_093841.jpg From a reservoir A whose surface elevation is 225 m, water is pumped through 1200 m. of 300 mmø pipes across a valley to a second reservoir B whose level is at elev. 240 m. During pumping, the pressure is 550 kPa at a point on the pipe midway of its length at C and at elevation 195 m. f a pump is installed near the outlet of the reservoir A and assuming f= 0.02. EL 240 El. 225 600 mm 300 mme 300mm 600m EL 195 O Compute the discharge flowing in the pipeline. Compute the head added due to the presence of the pump. O Compute the horsepower exerted by the pump.
A reservoir A with elevation 30m connected with a pump to rise the water into two reservoirs B and C 90m and 60 m respectively the amount of flow from J to B is equal 0.11 m/sec use the following data to determine the flow in each pipe and the power of the pump: LAJ 450 m, DaJ = 300 mm, LJB= 300 m, DJB = 200 m, Q JB = 0. m'/sec, LJc 600, D Jc = 150 mm,f (all Pipes) 0.02
A 90% efficient pump lifts water from a lower reservoir a shown in the figure. The head loss in the 150mm pipe is 3 times the velocity head in that pipe and the head loss in the 100mm pipe is 20 timew the velocity head in that pipe. A.If the desired flow rate is 20L/s ehat shoukd be the powet input of the pump in Kw? Choices: 42.9,28.8,32.0,38.6 B.Compute the pressure head, in m of water, at the suction line before the pump Choices: 12.39,10.29,9.74,7.56 C.Compute the pressure head,in m of water, at the discharge line right after the pump. Choices: 156.26,136.80,139.53,145.20
Q) Calculate velocity and flow rate of fluid (Water) in pipes. Also, determine the power of the pump, and the elevation of water in reservoir D. Finally draw E.G.L. of the following system. Ignore miner head losses. The height of energy at point C is 150 m. npump = 80% Pipe No. Diameter (m) Length (m) Friction factor (f) 1 0.2 1000 2 0.25 2000 0.025 0.10 250 4 0.15 500 120m E= ? D 100m A 12M В Pump
Two reservoirs A and B have elevations of 250m and 100m respectively. It is connected by a pipe having a diameter of 250mm diameter and length of 100m. A turbine is insatalled at a point in between reservoirs A and B. If C=120, compute the following if the discharge flowing in the pipe is 150liters/sec. Head loss of pipe due to friction. The head extracted by the turbine. Power generated by turbine
Calculate the required pump power since the velocity of the water in the pipe is v=1.91 m/s pwater=1000kh/m^3 μ=1.307x10^-3
A reservoir discharges a liquid to the atmosphere through a horizontal of pipes. Thepipeline consists pipe A (D= 10 cm & L = 25 m) and pipe B (D= 12 cm & L = 35 m) areconnected in series. The water level in the tank is 10 m from centreline pipe entranceand f = 0.02 for both pipe. Calculate the discharge by considering all losses.
9.The pump shown delivers 115 li/s of oil, sg = 0.84, toreservoir D at elevation 72 m. The energy lost in thesuction line is 3.2 J/N and in the discharge line is 7.6 J/N. a.Compute the total head added by the pump. b.How many kW does the pump supply the system? c.If the pump is 85% efficient, how much power does it need?
SITUATION 2: Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Elev 80 ha hez Elev 70 B 4000 m- 250 mm f-0.018 he 3500 m f- 0.018 Elev 60 Pipe 1: L= 5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L= 3500 m 5000 m - 300 mm f= 0.018
he water surface in reservoir A is 6m. higher than that in reservoir B. A 150-mm diameter pipe 270-m long leads from A to a point here it connects with a 100-mm diameter pipe 150-m long, leading from B, both discharges into a 200-mm diameter pipe discharges 40 liters/sec, find the difference in elevation between the end where it discharges into the air and the water surface in reservoir A. Use n = 0.011 for all pipes.
Consider the figure below. The pump supplies water from reservoir A to reservoir B through the 500mm o pipe, 600m long. Using f = 0.02 and the hydraulic grade line shown, determine the following: a) power supplied by the pump, b) power loss by the turbine, and elevation maintained by reservoir B. El. 200 hfj El. 190 НЕ El. 180 hf, B El.100 A P TURBINE PUMP ANSWER: a. Power = 1557.828 kW, b. Power = 155.7828 kW c. Elevation of B = 170 m %3D