3. A balanced Y-connected load having an impedance of 72+j212/q is connected in parallel with a balanced A- connected load having impedance of 150 0° /q. The parallel loads are fed from a line having an impedance of j12/q. The magnitude of the line- to-line voltage of the Y-load is 7650V. a) Calculate the magnitude of the current in the line feeding the loads. b) Calculate the magnitude of the phase current in the Y-connected load. c) Calculate the magnitude of the phase current in the A-connected load.

3. A balanced Y-connected load having an impedance of 72+j212/q is connected in parallel with a balanced A- connected load having impedance of 150 0° /q. The parallel loads are fed from a line having an impedance of j12/q. The magnitude of the line- to-line voltage of the Y-load is 7650V. a) Calculate the magnitude of the current in the line feeding the loads. b) Calculate the magnitude of the phase current in the Y-connected load. c) Calculate the magnitude of the phase current in the A-connected load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.44P: Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a...

See similar textbooks

Similar questions

In a balanced system, the phasor sum of the line-to-line voltages and the phasor sum of the line-to-neutral voltages are always equal to zero. (a) False (b) True
Consider a three-phase Y-connected source feeding a balanced- load. The phasor sum of the line currents as well as the neutral current are always zero. (a) True (b) False
Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a series impedance of (0.4j2.7) per phase. One of the loads absorbs 560 kVA at 0.707 power factor lagging, and the other 132 kW at unity power factor. The line-to-line voltage at the load end of the line is 2203V. Compute (a) the line-to-line voltage at the source end of the line. (b) the total real and reactive power losses in the three-phase line, and (c) the total three-phase real and reactive power supplied at the sending end of the line. Check that the total three-phase complex power delivered by the source equals the total three-phase comp lex power absorbed by the line and loads.
Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
Two balanced Y-connected loads in parallel, one drawing 15 kW at 0.6 power factor lagging andthe other drawing 10 kVA at 0.8 power factor leading, are supplied by a balanced, three-phase,480-volt source.a. Draw the power triangle for each load and for the combined load.b. Determine the power factor of the combined load and state whether lagging or leading.c. Determine the magnitude of the line current from the source.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
1. A wye-connected-load and a delta connected load are supplied by a four-wire 400 V three-phase, 50 Hz system. The connection for the wye loads are 2/20° ohms at line a, 30/50°V to line c and 6/75° ohms to line b. the connections for the delta loadare 50/30° ohms between lines a and b, 25/-60° ohms between lines b and c, and 17.3/90° ohms between lines a and c. Find the current on line b. 2. A wattmeter reads 5,540 W when the current coil is connected in phase a and the voltage coil is connected between the neutral and phase a of a balanced 3-phase system supplying a balanced load of 30 A at 400 V. What will be the reading of the instrument if the connections to the current coil remain unchanged and the voltage coil is connected between phase b and c? Take a-b-c phase sequence.
5. The figure below shows two star connected loads with three phase power. The voltage source is 120Z0°. The loads are Z₁ = 10 + j4 № and Z₂ = 2 +j3 №. The cables are negligible. Calculate: a) the line and phase current. b) the real power from the source. c) the reactive power of the circuit. Is V N Z₁ Z₁ Z₁ Z₂ Z₂ N N Z₂
The Figure shows a balanced Y-A 3Ø circuit. The phase voltages of the Y-connected source are V, = 11020°, V, = 1102 - 120° and V. = 1102120°, Volts. The line impdedances are Z,=10+j5 Q each. The impedances of the A-connected load are ZA = 75+j255 N each. Determine: Line Currents, Phase Currents (load), Power drawn by the load. Ve ZA Vb
A balanced three-phase Y-connected source with positive sequance has an internal voltage of 120 V/phase. The source feeds a balanced three-phase Y-connected load having an impedance of 39 + j28 N /phase. The impedance of the transmission line connecting the source to the load is 1+ j20/phase. The a- phase of the source is the reference voltage. a) Draw the equivalent per-phase-circuit for the phase "a". b) Calculate the three line currents in the transmission lines. c) Calculate the three phase voltages at load. d) Calculate the three line-to-line voltages at the terminals of the load. e) Calculate the total average power in watts delivered to the load. f) Calculate the total complex power in VA delivered by the source.
A balanced three-phase three-wire system has a line voltage of 500 V. Two balanced Y-connected loads are present. One is a capacitive load with 7 - j2 ohms per phase, and the other is an inductive load with 4 + j2 ohms per phase. a) The magnitude of the phase voltage is V. Do not write units, no decimal places. b) The magnitude of the line current curent is A. Do not write units, round off to one(1) decimal place. c) the total power drawn by the load is kW. Do not write units, no decimal places. d) the power factor at which the source is operating is Round off to three (3) decimal places.