3) A. A parallel circuit with the following parameters the total applied voltage is 150<-30. Current at branch one is 6.5<30. Current at branch two is 5<-53. Draw the phasor diagram of V-I and find the impedance of each branch and the total admittance B. Z1= 15 ohm, Z2= 8 - j12 are connected in parallel .Total power of the circuit is 2000 watt find the P1 and P2.

3) A. A parallel circuit with the following parameters the total applied voltage is 150<-30. Current at branch one is 6.5<30. Current at branch two is 5<-53. Draw the phasor diagram of V-I and find the impedance of each branch and the total admittance B. Z1= 15 ohm, Z2= 8 - j12 are connected in parallel .Total power of the circuit is 2000 watt find the P1 and P2.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Similar questions

For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
1) Referring to the circuit as in Figure 1, transform the circuit in phasor domain representation.2) Determine the value of total impedance, ZT3) Determine the value of total current, IT4) Determine the value of branch current, I1 and I25) Determine the value of voltage across resistor, R1, R2 and R36) Determine the value of voltage across capacitor, C1 and C27) Determine the value of voltage across inductor, L.
Explain current divider rule in ac circuits with two parallel impedances Z1 and Z2. Calculate the currents I1 and I2 in phasor form for the circuit given in figure.
Three impedances, Z1 =10020.Q, Z2 =63.2518.43.2 and Z3 =1002-90•Q are connected in star. Convert the star to an equivalent delta connection. And draw the star network and also the equivalent of delta connection
The impedance Z1 = 6+j8, Z2 = 8 -j6 and Z3 = 10+j0 ohms measured at 50Hz from three branches of a parallel circuit. This circuit is fed from a 100-volt 50-Hz supply. A purely reactive (inductive or capacitive) circuit is added as the fourth parallel branch to the above three-branched parallel circuit so as to draw minimum current from the source. Determine the value of L or C to be used in the fourth branch and also find the minimum current.
find total equivalent resistance and reactance and total impedance transferred in primary side.
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
calculate phasor currents I1 and I2 in the circuit shown below
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.