This is not a quiz question. It is part of a review packet. Free Body Diagram and Kinetic Free Diagram needed. 3). A barge initially at rest carries a 1000 lb crate. The barge weighs 3 tons and is equipped with awinch which is used to move the crate along the deck of the barge. Neglecting any frictionbetween the crate and the barge, determine the velocity of both the barge and the crate whenthe winch is drawing in rope at the rate of 9 ft/sec.FULL CREDIT AWARDED ONLY FOR CORRECT FBD & KFD INCLUDED IN SOLUTIONANS. B=BARGE, C = CRATE, V³ = 1.29 fps, Vc = -7.71 fps

To solve this problem, we'll apply the principle of conservation of momentum. Since there are no…

Answered: 3) . A barge initially at rest carries…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Drew is pushing a 12.0-kg box on a floor until he runs into a horizontal spring. The values of force for a few different values of horizontal position x are (x, F): (-2, 10), (-1, 10), (0, 10), (1, 15), (2, 20), (3, 25), (4, 30). a. What is the coefficient of friction? b. What is the work done by Drew's pushing force from x = 0 m to x = 7 m, where x = 0 m corresponds to the initial contact with the spring? c. What fraction of this work goes into heat?
A Center Raft A person is standing at one end of a uniform raft of length L that is floating motionless on water, as shown above. The center of mass of the person-raft system is a distance d'from the center of the raft. The person then walks to the other end of the raft. If friction between the raft and the water is negligible, how far does the raft nove relative to the water? L/2 B L C d/2 Ⓡ O d Center of Mass of System 2d in
Problem: A person on a bicycle of mass 85 kg ( including the bicycle) can slow down at velocity of 3.60m/s? safely without skidding when approaching the next stop on the road. a. Draw the free-body diagram, including all the forces that apply to the problem. b. How would the free body diagram look on the person one the bike if the road was inclined uphill at 18 degrees? How would its deceleration change if the road was increased to 18 degrees? c. If the bieyelist elimbs up the hill at a speed of 8.0km/h because of the air resistance. What force would be necessary to climb the hill at the same speed with the same air resistance?
PRACTICE PROBLEM 8.2 two minecarts are connected as shown below. Friction is negligible. Assume that x1 & x2 is the displacement of the mass of the first cart and the mass of the second cart from their starting positions respectively. KI m, www m₂ If you know that: Both minecarts have a mass = 2 kilograms Spring constant (kl)=72N/m Spring constant (k2)=108N/m Spring constant (k3)=72N/m Differential eq: ď = [ 3 x K3 www Make a second order differential equations system that models the situation and find the general solution to the system you make. General solution: [x₁(t) [2²2(b)] = [-] (a₁ cos (-) + b₁ sin (-)) + [-] (0₂0 [x₂(t) (a2 cos (-) + b₂ sin (-))
Help me please
! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A tractor-trailer rig with a 2000-kg tractor, a 4500-kg trailer, and a 3600-kg trailer is traveling on a level road at v = 90 km/h. The brakes on the rear trailer fail and the antiskid system of the tractor and front trailer provide the largest possible force which will not cause the wheels to slide. The coefficient of static friction is 0.75. Trailer Trailer Rig 00 00 00 Determine the shortest time for the rig to come to a stop. (You must provide an answer before moving to the next part.) The shortest time for the rig to come to a stop is S.
Task 6 An industrial trolley of mass 350 kg is used to transport equipment and materials to a workstation within the R and D section. Initially the trolley is at the top of a 15 m high hill, which is inclined at 10º to horizontal as shown and travelling at 6 m/s before rolling down into the station. On reaching the bottom of the hill, brakes are applied to the trolley to slow it down to 0.25 m/s in 4.5 m. Determine: The braking force that slowed the trolley down The time it takes the trolley to slow down The deceleration of the trolley
ame. Matric No: Instruction: Answer according to the given sequence, unable to do this will lead to zero mark!!!! And please read the question!!!!!. As shown in the figure, forces are applied to the box that has a mass of 75 kg. Given that the coefficient of kinetic friction between the box and surface is uk = 0.297. If the box is originally at rest and currently moving with a speed of v = 5 m/s: 450 N 200 N 35° 50° 1. Draw the free body diagram and find the normal and friction force of the box. . 2. Find its initial and final kinetic energy - 1** 3. Determine the distance that the box has travelled by using the principle of work and energy [/ 4. Calculate each work that is done to the box [1. 1 of 1
Block A has a weight of 60 lb and block B has a weight of 10 lb. Neglect friction and the mass of the cord and pulleys. The figure shows a system of pulleys and blocks. Block A is located on an inclined surface with a slope of three-fourths. Block B is vertically suspended by a cord that goes over a pulley located at the top end of the inclined surface. The cord then goes downward and to the left, parallel to the slope, then it goes over a pulley fixed to the upper right end of block A. Then the cord goes upward and to the right parallel to the slope. The end of the cord is fixed to the anchor. Determine the speed of block A after it moves 5.7 ft down the plane, starting from rest.
In a governor of the Hartnell type the arms of the bell-crank leversare equal in length, and those carrying the operating masses arevertical when the governor is rotating at its mean speed of 775rev/min, with the masses moving in a circle of 175 mm diameter -The usual central controlling spring is replaced by two paralleltension springs direetly connecting the operating masses. Find(a) the magnitude of each operating mass if a force of 90 N isrequired at the sleeve to maintain it in the mean speed positionwhen the specd is increased from 775 to 800 rev/m in(b) the stiffness, or rate, of each spring if the ratio of sleevemovement to increase of speed is 1 mm to 10 revImin when inthe mean speed position.
3B. 100-N block on a rough 30°-incline is acted upon by a force P as shown causing it to accelerate at 2 m/s2 down the plane. The coefficient of kinetic friction is 0.30. (a) Draw the FBD of the block (b) Find the magnitude of P. 20° 30°
Problem No. 1 A 14.0-kg Box is lowered vertically by a 16 mm diameter cable in which there is 163 N of tension at a given instant. What is the acceleration of the Box? Is it up or down?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS