600 N Problem 5: Fatigue A bicycle crank experiences cyclic loading due to the force applied by the rider's feet. The maximum stress occurs at the angle shown. Assume the minimum stress is zero (the rider applies no force on the upstroke). The rider applies a force of 600 N. Neglect torsion in the crank. The crank is 165 mm long and has a rectangular 15 mm G 165 mm ☑ 12 mm cross-section with a width of 12 mm and height of 15 mm. It's made of steel: Sy = 290 MPa, Sut = 360 MPa, Se = 110 MPa, σ = 460 MPa, b = -0.1. a) Calculate the safety factor against yielding on the first pedal stroke using the max. shear stress criterion.

600 N Problem 5: Fatigue A bicycle crank experiences cyclic loading due to the force applied by the rider's feet. The maximum stress occurs at the angle shown. Assume the minimum stress is zero (the rider applies no force on the upstroke). The rider applies a force of 600 N. Neglect torsion in the crank. The crank is 165 mm long and has a rectangular 15 mm G 165 mm ☑ 12 mm cross-section with a width of 12 mm and height of 15 mm. It's made of steel: Sy = 290 MPa, Sut = 360 MPa, Se = 110 MPa, σ = 460 MPa, b = -0.1. a) Calculate the safety factor against yielding on the first pedal stroke using the max. shear stress criterion.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter4: Shear Forces And Bending Moments

Section: Chapter Questions

Problem 4.5.37P: The inclined beam represents a ladder with the Following applied loads: the weight (W) of the house...

See similar textbooks

Similar questions

The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is
Q1: The arrangement of a transmission brake is shown in the figure. The arms are pivoted at O and, when force is applied at the end of the hand lever, the screw AB will rotate. The left-and right- hand threads working in nuts on the ends of the arms will move the arms together and thus apply the brake actuating force equally. A B 12cm The drum is 17.75cm diameter, and the angle subtended by each block is 90°. the friction material lining width is 4cm. Assuming a coefficient of friction for the braking surfaces that is equal to 0.30 Determine the force required by the screw AB to set the brake torque on the drum equal to 200 N-m. 17 75cm 12cm 46 35cm Torqueleft= TorqueRight= 97.40 N.m 6 35cm 102.60 N.m
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.
The figure attached shows a crank loaded by a force F=300 lbf that causes twisting and bending of 3/4 -in-diameter shaft fixed to a support at the origin of reference system. Calculate the following: The internal forces at A, B, and C. Refer to the FBD figure and table provided below. All units shall be in lbf-in for moments and torques, lbf for forces. Determine the maximum normal and shear stress at A. DRAW THE STRESS ELEMENT/S AND SHOW APPROPRIATE FORCES. Units shall be in ksi.
The electric motor exerts a 500-N-m torque on the aluminum shaft ABCD when it is rotating at a constant speed. The torques exerted on pulleys Band Care as shown. Take a = 1.4 m, b= 0.9 m, and G= 27 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 300 N. m 200 N. m 45 mm 44 mm 40 mm Im Determine the angle of twist between Band C. The angle of twist between Band Cis|
Since the force on the wheel is F = 3.4 kN, as in the figure, calculate the joint force FA and the spring force FB- +100 650 009 200 C B A
QUESTION 2: For the nose landing gear of an aircraft shown in the figure, calculate the internal forces at the vertical section at point A. -150 mm 20 mm- 60° 300 mm -175 mm 12 kN
PROBLEM 2: For the nose landing gear of an aircraft shown in the figure, calculate the internal forces at the vertical section at point A. -150 mm 20 mm 60 300 mm -175 mm 12 kN
Adjustable pliers hold a round metal bar as a machinist grips the handles with P = 43 N. Using the free body diagram shown for the combined lower jaw and upper handle, calculate the force A that is applied to the bar. Assume lh = 160 mm and l2 = 15 mm. (Express your answer using three significant figures.) A =
plz help before -ront The shaft is supported at its ends by two bearings A and B and is subjected to the forces applied to the pulleys fixed to the shaft. (Figure 1) The T₁ 410-N forces act in the - direction and the 200-N and 80-N forces act in the +y direction. The journal bearings at A and B exert only y and components of force on the shaft. Figure lashel but sol is 300 mm A 200 mm 2 150 mm 150 mm ✓ 200 mm 400 mm B. 200 N 200 N 80 N 80 N 1 of 1 ▾ Part B Determine the resultant shear force in the y direction on the cross section at C Express your answer to three significant figures and include appropriate units. (Vc)y=245.714 Submit Part C Submit * Incorrect; Try Again; 3 attempts remaining Check your signs. (Vc),= 175 ▾ Part D Determine the resultant shear force in the direction on the cross section at C. Express your answer to three significant figures and include appropriate unite. T= 10 ▾ Part E Previous Answere (Mc) Submit M ^ Part Fi * Incorrect; Try Again; 5 attempts remaining…
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 820 lb is applied to the tire at point C at an angle of 0 = 22° as shown. Assume the connection of the wheel to member AB is rigid. hs hy hi F BY NC SA W4. W, Ws 2013 Michael Swanbom Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value hi 10 in Wi 8.8 in h2 15.6 in W2 5.6 in h3 18.1 in W3 10.8 in h4 10.9 in WĄ 7.4 in h5 4.9 in W5 9.3 in For all answers, take x as positive to the right and y as positive upward. At point B, member AB exerts a force of B = j lbs on member BHE. At point A, member AD exerts a force of A + j lbs on member AB. At point H, shock GH exerts a force of H = i + i lbs on member ВНЕ. At point E, the magnitude of the force exerted on the car body by member BHE is lbs. At point D, the magnitude of the force exerted on the car body by member AD is lbs. At point G, the…
touch &O O166% 00:27 MENG250 - Practice Assign... Problem 2-15 Determine the design angle ø (0° < ø< 90°) between struts AB and AC so that the 400-lb horizontal force has a component of 500 lb directed from A towards C. What is the component of force acting along member AB? Take 0 = 40°. 400 lb A te B