PROBLEM 3: A right-angled rigid pipe is fixed to a wall at A and is additionally supported through the cable CD as shown in the figure. The tension in the cable is 3 kN. Neglect the weight of the pipe. Use the Right-Hand-Rule to indicate the direction of the moment. [8] Calculate total force reaction at A. (ANSWER: 3.00 KN) [9] Calculate the moment reaction (including correct sign) at A about z-axis. (ANSWER: 2.168 KN-m) [10] Calculate the moment reaction (including correct sign) at A about x-axis. (ANSWER: -0.843 KN-m)

Q: Suppose that P₁ = 600 lb and P₂ = 800 lb. Suggestion: Use the sections shown in (Figure 1). Figure 6…

A:

Q: A weight W = 300# is suspended by a cable system as shown in the figure. a. Calculate the moment of…

A: a) Moment of force W about point D can be determined as

Q: 7. The horizontal stick of length, L, shown in the figure is uniform and weighs tensions, T1 and T2,…

A: given:W=500Nweight of stick=200N

Q: Answer FOUR questions ONLY selecting TWO questions from SECTION A. 1. (a) The vertical structure…

A: Find the reaction at point A and stress in steel bar and aluminium tube.

Q: 3.33 m Each traffic light weighs 400 N 0.6 m 3.33 m 1000 3.33 m (1) For the cable supported with…

A:

Q: 4- Şekildeki mekanizma ile E ucundaki tahta sıkıştırılacaktır. Buna göre uygulanan düşey P kol…

A:

Q: A boom AB is supported in a horizontal position by a hinge A and a cable which runs from C over a…

A: The FBD of the horizontal boom. Determine the tension in the cable and the components of reaction at…

Q: 2.) The plate is supported by a pin in a smooth slot at B. What are the reactions at the supports?…

A: Given:The diagram of the problem is given below;

Q: Find the value of C & D so that the four forces shown in Figure produce an upward resultant of 300lb…

A:

Q: The ship ladder in the figure is 1500 N and its center of gravity is at G. What must be the rope…

A:

Q: Numerical problem 3.2: The beam on the figure is subj of the beam is 3 m. The distance from the…

A:

Q: A bent pipe is attached to a wall with brackets as shown. A force of F = 105 lb is applied to the…

A:

Q: Problem # A) Assuming it can ONLY take tension, find the Tension in the cable "AC“: B) Calculate the…

A: For the given figure  To determine  (a) tension in cable AC  (b) Reaction at C and B

Q: The Moment about "C" (in Nm) = The Moment about "D" (in Nm) =

A:

Q: Determine the reaction forces at points A, B & C. All supports have 2 forces. The first is…

A: The reaction forces at .FBD:The free-body diagram is shown below.

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A: Given F =180 N

Q: 2) The ABO vertical arm whose mass m is neglected in the figure is kept in balance with a spherical…

A: A spherical joint will experience all the three components of forces at the support. So, the…

Q: The system shown in the figure is subjected to a force of F = 509 N 1) Calculate the magnitude of…

A: Given data as per the question Force =509 N

Q: RAX RAY 0 F₁ KN F₂ kN D The figure above is a pin-joint frame with angle = 30° between members AF…

A:

Q: The system in the figure is in equilibrium. A concrete block of mass 265 kg hangs from the end of…

A: Given-To Find-(i) Tension  in the cable(ii) horizontal component of Force on strut from hing(Iii)…

Q: A stepped bar is held in equilibrium by several forces acting at different points along the length,…

A:

Q: Need help please Include all units and steps

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: A member is loaded with force system as shown in figure.  Find the Moment about A , B, C, D and E…

A:

Q: The figure shows a frame with negligible mass, keeping a 50-lb weight in equilibrium. The smooth…

A:

Q: Calculate the moment at point (A) of the forces shown in figure. T=10 2.5 m-1 T-3N 2.5 m T T3=6 N…

A:

Q: 3. For the truss shown below, the force P is 320 N. Find the support reactions at A and C. Using…

A:

Q: A V₁ = M₁= 20 4.88 (b) A point #₂ = V₂ = M₂= Note: Express your answers following the standard sign…

A: Given data  q = 400lb/ft F = 14 kips Lf = 17ft L = 24 ft Find the shear force and bending moment at…

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A:

Q: The specialty wrench shown in the figure is designed for access to the hold-down bolt on certain…

A:

Q: Find components of reaction at A (use journal bearing reaction for point A reactions) and also Find…

A:

Q: A member is loaded with force system as shown in figure.  Find the Moment about A , B, C, D and E…

A: F1= 70 N, F2 =55 N, F3 =10 N, F4 =20 N, F5 =45 N, AB =110  m, Point C is in the mid of AE, CD = 35m,…

Q: The prismatic bar AC is supported by a hinge at C and cable ADB that runs through a frictionless…

A:

Q: The tractor shovel shown (Figure 4) carries a 500 kg load that has its center of mass at H. The…

A:

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A: Given that The force P→ is 19i^-10j^ KNThe coordinates from the figure are:A 2,0,-3; B (0,6,0); C…

Q: 20 kN 30 KN 40 kN 6 m

A:

Q: A member is loaded with force system as shown in figure. Find the Moment about A, B, C, D and E…

A: Now, given that AE = 120m AC = CE = 120/2 = 60m AB = 80m, CD = 35m Now, calculate the moment about…

Q: The 2D truss shown in the figure below is loaded with two forces F₁ = 40 N and F₂ = 50 N. Compute…

A:

Q: A 1480-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the…

A:

Q: A cantilever beam is free of support at point A and is clamped at the point B, as shown in the…

A: Given:- w=95N/m L=5m To find: a) Support reaction at B 2) Support reaction moment at B

Q: A member is loaded with force system as shown in figure. Find the Moment about A, B,C, D and E Where…

A:

Q: at A in kN.   Calculate the magnitude of the tension in cable BD in kN Calculate the magnitude of…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.