The double - riveted joint connects two plates which are each 3.0 mm thick, and the rivets have a diameter of 4 mm., if the failure strength of the rivets in shear is 370 N/mm? and the ultimate tensile strength of the plate is 465 N/mm?, determine the necessary rivet pitch b (mm) if the joint is to be designed so that failure due to shear in the rivets and failure due to tension in the plate occur simultaneously. Calculate also the joint efficiency n (%). 3 mm 4 mm diameter

The double - riveted joint connects two plates which are each 3.0 mm thick, and the rivets have a diameter of 4 mm., if the failure strength of the rivets in shear is 370 N/mm? and the ultimate tensile strength of the plate is 465 N/mm?, determine the necessary rivet pitch b (mm) if the joint is to be designed so that failure due to shear in the rivets and failure due to tension in the plate occur simultaneously. Calculate also the joint efficiency n (%). 3 mm 4 mm diameter

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 20-mm-thick plate is bolted to the flange of a T-beam to form a 200 mm 20 mm built-up beam. If the beam is subjected to a vertical shear force of V = 200 kN, determine (a) the maximum shear stress in the beam, 10 mm 300 mm (b) the required spacing s of the bolts. The diameter of each bolt is 19 mm, and the allowable average shear stress in the bolts is 140 MPa. 10 mm
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten A plate having a width of 400 and a thickness of 20mm is to be connected to two plates with thickness of 12mm by four rivets. The allowable shear stress for the rivets is 150 MPa and for bearing is 1.35 Fy. If the yield strength and the ultimate strength is 248 MPa and 400 MPa respectively. Determine the Following: a.) Required diameter of rivets w/o exceeding the aloowable stress in the shear. b.) Required diameter of rivets w/o exceeding the allowable stress in bearing. c.) Required diameter of rivets w/o exceeding the allowable stress in tension.
STRENGTH OF MATERIAL(SIMPLE STRESS) PLEASE INCLUDE FBD 100% GUARANTEE UPVOTE
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
The assembly consists of a bronze tube and a threaded steel bolt. The pitch of the thread is 1/32 in. (one turn of the nut advances it 1/32 in.). The cross-sectional areas are 1.5 in? for the tube and 0.75 in? for the bolt. The nut is turned until there is a compressive stress of 4000 psi in the tube. Find the stresses in the bolt and the tube if the nut is given one additional turn. Use E = 12 x 10° psi for bronze and E = 29 x 10° psi for steel. Bronze tube 40 in.-
A plate with width of 300 millimeters and thickness of 20 milimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters by 25 millimeters diameter rivets. The rivets holes have a diameter 2 millimeters larger than the rivetdiameter. The plate is A36 with yield strength F, = 248MP.. Allowable tensile stress on net area is 0.6Fy and allowable bearing stress of 1.3Fy. The rivets are A502, Grade 2, hot-driven rivets with allowable shear stress of 150MPA. 1. Detemine the maximum load that can be applied to the connection with consideration to the yielding failure in the plates. 2. Detemine the maximum load that can be applied to the connection with consideration to the fracture failure in the plates. 3. Detemine the maximum load that can be applied to the connection without exceeding the allowable shearing stress in the rivets. 4. Detemine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between…
A 12.5-mm round structural steelrod is loaded in tension to fracture. The 200-mm gagelength of the rod was marked off in 25-mm lengthsbefore loading. After the rod broke, the strain in the50-mm containing the fracture was found to be 0.45mm/mm, and the total elongation of the other 150 mmwas found to be 37.5 mm. Determine the averagestrain for the 200-mm gage length.
The following steel member is connected to the gusset plate via two longitudinal welds. The width of the member is 58 mm and the length of the weld is 87 mm. The yield stress is 300 MPa and the ultimate stress is 675 MPa. The gross area of the member is 700 mm^2 . a. What is the tensile design yield strength in KN? b. What is the tensile design rupture strength in KN? c. If a tensile load of 85 KN is requiredfor the member, what is the minimum factor of safety for the steel member?
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the minimum pin diameter. Use Shear stress-D0.4"Yield strength. Assume material is 1020 hot-rolled steel. * P2 Shear Planes Pin
The structure shown below is hinged to fixed supports at A and C. The bars are each 4 in. by 4 in. in section. Compute the maximum tensile stress developed in bar CB assuming the pin connections at A, B, and C are frictionless. Group of answer choices 2300 psi 2800 psi 1150 psi 4600 psi
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.