Question 1: The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber=20MPa Allowable shear strength of the steel = 200MPa 1,000N tr 45 mm Rubber band Dpin Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt? Rubber band 1,000N

Question 1: The rubber band given below is subjected to the following tensile loading. Calculate the minimum thickness of the rubber (tr) and the minimum steel pin diameter (Dpin) so that the structure does not fail. Consider: Allowable tensile strength of the rubber=20MPa Allowable shear strength of the steel = 200MPa 1,000N tr 45 mm Rubber band Dpin Reflection: 1) How would you solve this problem if a Factor of Safety was given? 2) Are there any other dimensions worth calculating for the rubber belt? Rubber band 1,000N

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
X Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.42 in.? and an elastic modulus of 2180 ksi. Bar (2) has a cross-sectional area of 1.139 in.? and an elastic modulus of 4150 ksi. Assume L;-23 in., L2-41 in., Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Determine the horizontal deflection of end Crelative to end A. R (1) (2) P L1 L2 Answer: UCIA - i 0.0725 in.
1. The hanger assembly shown supports a 4500-kg pipe. The working stresses for each of the hanger assembly components are as follows: Tensile Stress in the Hanger Rod ≤ 140 MPa Shearing Stress in the bolt ≤80 MPa Bearing Stress between the bolt & the Bottom Strap ≤ 120 MPa Calculate the following: a. Required diameter of the hanger b. Required diameter of the bolt
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
As shown in the figure below, a bronze bar is affixed between a steel bar and an aluminum bar. Axial loads are applied at the positions indicated. If the largest value of P that will not exceed an overall deformation of 4.0 mm, or the following stresses: 150 MPa in the steel, 130 MPa in the bronze, and 90 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. determine the stress in the bronze, steel, and aluminum
3. The distribution of stress in an aluminum machine component is given (in megapascals) by Ox = y + z? Oy = x + z Oz = 3x + y Txy = 3z2 Tyz = x Txz = %3D Calculate the state of strain at a point positioned at (1,2,4). Use E=70 GPa and v = 0.3
A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar segments are L1=0.3 m and L2=0.15 m. The radius at the transition R = 1.25 mm and the modulus of elasticity is 90 GPa, the bar product of the load p elongates 0.12 mm normal stress and maximum stress