2. In voice morphing application of DSP a person voice is captured and sampled for 50 second by using 24-bit ADC at a sampling frequency of 40 kHz. The samples are stored on a memory chip. i. What is the minimum memory size in bytes required to store all the samples? ii. How long the signal must be sampled to store the samples in 4 GB hard disc. iii. What should be the highest frequency component of the signal?

2. In voice morphing application of DSP a person voice is captured and sampled for 50 second by using 24-bit ADC at a sampling frequency of 40 kHz. The samples are stored on a memory chip. i. What is the minimum memory size in bytes required to store all the samples? ii. How long the signal must be sampled to store the samples in 4 GB hard disc. iii. What should be the highest frequency component of the signal?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Similar questions

Q2/ The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ±0.1% (full scale). The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of -10 to +10 volts. Find the minimum sampling rate required. i) ii) Find minimum bit rate required in the PCM signal. Find the number of bits in each PCM word. iii) iv) Find the minimum absolute channel bandwidth required for the transmission of the PCM signal.
Choose the correct answer low HDOP (Horizontal Dilution of Precision) number such as2 indicates a ........................... a.poor fix b.good fix c.poor signal quality d. good signal quality
b. Explain how to decide the sampling rate for a multi-frequency input signal. c. An ADC with word length of 24 bits. If the input analogue signal range is 3.7 V, what is the resolution of this ADC? d. Consider a thermocouple giving an output of 0.5 mVrc. What will be the word length required when its output passes through an ADC if temperatures from 0°C to 120°C are to be measured with resolution of 1.5°C?. Assume 12V as system voltage.
1. With the help of Octave program perform the Modulation and Demodulation (AM) of information signal with carrier signal, through subplots with following signals a. Modulating signal b. Modulated signal c. Demodulated signal
What do you mean by fractional sampling rate conversion? Explain with an example of converting 48 kHz signal to 44.1 kHz signal using multi-stage fractional sampling rate converter. (ii) What are the effects of finite word length in digital filters
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
what causes aliasing? a, when the original analog signal is outside the voice band frequency range. b. when each cycle of the analog input signal is not sampled at least twice. c. is produced when the magnitude of a sample is rounded off to closest available level. d. the sample and hold circuit naturally introduces alias of the input.
2/ Information in an analog waveform, whose maximum frequency is 10 kHz, will be transmitted using a minimum sampling rate and a 32-PAM system. transmitted using a minimum sampling frequency and a 32-PAM system. The quantization distortion shall not exceed 0.01% of the The quantization distortion must not exceed 0.01% of the peak-to-peak value of the analog signal. a/ What is the minimum PCM word size to be used in the system? b/ What is the baud rate?
Make a signal flow diagram out of the data. Label everything properly.
Problem 2: The information in an analog signal voltage waveform is to be transmitted over a PCM system with an accuracy of ± 0.1 % of the peak-to-peak analog signal. The analog voltage waveform has a bandwidth of 100 Hz and an amplitude range of – 10 to + 10 Volts. Determine the minimum sampling rate required. b. Determine the number of bits in each PCM word. c. Determine the minimum bit rate required in the PCM system. d. Determine the minimum absolute channel bandwidth required for the transmission of the PCM signal.
Q3) Twenty voice signals are sampled uniformly and then time division multiplexed. The sampling operation uses flat samples with 2 us duration. The multiplexing operation provides for synchronization by adding an extra pulse of 2 us. the highest frequency component of each signal is 3.4 kHz. a. For sampling rate of 8 kHz, calculate spacing between successive pulses of multiplexed signal. b. For Nyquist rate, repeat part a.
What do you mean by fractional sampling rate conversion? Explain with an example of converting 48 kHz signal to 44.1 kHz signal using multi-stage fractional sampling rate converter