what causes aliasing? a, when the original analog signal is outside the voice band frequency range. b. when each cycle of the analog input signal is not sampled at least twice. c. is produced when the magnitude of a sample is rounded off to closest available level. d. the sample and hold circuit naturally introduces alias of the input.

what causes aliasing? a, when the original analog signal is outside the voice band frequency range. b. when each cycle of the analog input signal is not sampled at least twice. c. is produced when the magnitude of a sample is rounded off to closest available level. d. the sample and hold circuit naturally introduces alias of the input.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.3: Signal System

Problem 1R

See similar textbooks

Similar questions

Which statement is true? a. In FSK, the modulating signal and the carrier signal are both analog b. In FSK, the modulating signal and the modulated signala re both digital c. In FSK, the modulating signal and the modulated signal are both analog d. In FSK, the carrier signal is analog and the modulating signal is digital
What do you mean by fractional sampling rate conversion? Explain with an example of converting 48 kHz signal to 44.1 kHz signal using multi-stage fractional sampling rate converter
2a. Assume a digital to analog conversion system uses a 10-bit integerto represent an analog temperature over a range of -25oF to 125oIf the actual temperature being read was 65.325oF, what would bethe closest possible value that the system could represent? 2b. What is the minimum sampling rate needed in order to successfullycapture frequencies up to 155 KHz in an analog signal?
Q5/ The information in an analog waveform with maximum frequency fm transmitted over M-level PCM system where the number of quantization levels is M = 16. The quantization distortion is specified not to exceed 1% of peak-to-peak analog signal. = 3 KHz is to be i) What would be the maximum number of bits per sample that should be used in this PCM system? (ans,n = 4 bits) What is the minimum sampling rate and what is the resulting bit transmission rate? ii) (ans.r > 24 x 103 bits/sec)
1. What are the advantages of sampling analog signals?
What is sample and hold circuits?
What is the physical meaning of sampling theorem? And Write down the corresponding expressions for low-pass analog signals and band pass analog signals. What happens if the sampling theorem is not satisfied when sampling an analog signal?
[0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of Qunta levels? b) Calculate what is the quantization interval? c)V=3.2 volts rounded to what quantization level? Let's draw with Quantalama level chart
1. a) An analog signal contains frequencies up to 12 kHz. (i) What range of sampling frequencies dose allow exact reconstruction of this signal from its samples? (ii) Suppose that we sample this signal with a sampling frequency Fs = 9 kHz. Examine with proper diagram what happens to the frequency component F1 = 6 kHz after passing through the digital to analog converter. (iii) Repeat part (ii) for a frequency component F2 = 11 kHz. b) Why is it necessary to introduce an analog low-pass filter before analog to digital converter? Illustrate the fact with necessary diagram.
4. Signal conditioning element basically takes the output of the sensing element and converts it into a form more suitable for further processing, usually in the form of a DC voltage, DC current or variable frequency AC voltage. The output of the sensing element is usually too small to operate an indicator or a recorder. Therefore, it is suitably processed and modified in the signal conditioning element so as to obtain the output in the desired form that is amplify the signal and filtering the unwanted signal. i. Describe the aliasing phenomenon. ii. Suggest a solution to minimize the effect of aliasing.
What is the minimum sampling rate needed in order to successfully capture frequencies up to 80MHz in an analog signal?
6. Draw the circuit diagram and find the value of 'X' bit for a digital to analog conver, if Vout = 126.9V, the input digital bit is 01X1, and Vref= -203.04V.