2. An electrical power transmission system has various equipment and parameters. As shown in the figure below, find a. load current (i load) b. Power losses in the transmission system 2.1) Use the method of moving the impedance value (referred). 2.2) Use the per-unit (pu) method. 380 V 50 Hz Generator IG 1:10 T₁ Iline Zline 0.25+j0.40 10:1 T₂ hoad Zload 6+j4

2. An electrical power transmission system has various equipment and parameters. As shown in the figure below, find a. load current (i load) b. Power losses in the transmission system 2.1) Use the method of moving the impedance value (referred). 2.2) Use the per-unit (pu) method. 380 V 50 Hz Generator IG 1:10 T₁ Iline Zline 0.25+j0.40 10:1 T₂ hoad Zload 6+j4

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.25P: Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows:...

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
Consider three ideal single-phase transformers (with a voltage gain of ) put together as three-phase bank as shown in Figure 3.35. Assuming positive-sequence voltages for Va,Vb, and Vc find Va,Vb, and VC. in terms of Va,Vb, and Vc, respectively. (a) Would such relationships hold for the line voltages as well? (b) Looking into the current relationships, express IaIb and Ic in terms of IaIb and Ic respectively. (C) Let S and S be the per-phase complex power output and input. respectively. Find S in terms of S.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
Explain the concept of FACTS (Flexible Alternating Current Transmission Systems) devices. How do they enhance the control and stability of power systems? Provide examples of FACTS devices and their applications.
What is the main direct cause of reactive power in AC system?A. Resistance of transmission linesB. Inductance and capacitance in the loadsC. Ideal transformer connected in the systemD. Power produced by generator2. “Reactive power in a system is dissipated generally as thermal energy?”A. TRUEB. FALSE3. Which of the following statements are correct for three phase circuit:A. Sum of all the three phase currents is zero in unbalanced networkB. Total power transfer to load is constant with timeC. Neutral conductor is same size in terms of material used as in single phase conductorsD. Net apparent power consumed is equal to real power
Q4/For the three-phase power network shown in Figure. the various components are: GI: 100 MVA, 0.30 pu reactance. G2: 60 MVA, 0.18 pu reactance. Transformers (cach): 50 MVA, 0.10 pu reactance. Inductive reactor X: 0.20 pu on a base of 100 MVA. Lines (each): 80 ohms (reactive); neglect resistance. with the network initially unloaded and a line voltage of 110 kV, a symmetrical short circuit occurs at midpoint E of line 2. Calculate the short circuit MVA to be interrupted by the circuit breakers A and B at the ends of the line. T3 38 L1 L2 G2 Bas 12 T4 Bus
Q2) A 13.2-kV single-phase generator supplies power to a load through a transmission line. The load's impedance is Zload = 500 236.87° ohm, and the transmission line's impedance is Zline = 60 253.1° ohm. To reduce transmission line losses to 0.0103 of its losses without using the transformers design and use two transformers T1 between the generator and the transmission line and T2 between the transmission line and the load.
a. i. Why do power systems operate in an interconnected arrangement? ii. How is the frequency controlled in a power system? iii. What is meant by the stiffness of a power system? b. Two 50 Hz power systems are interconnected by a tie-line, which carries 1000 MW from system A to system B, as shown below. After the outDage of the line shown in the figure, the frequency in system A increases to 50.5 Hz, while the frequency in system B decreases to 49 Hz. i. Calculate the stiffness of each system. ii. If the systems operate interconnected with 1000 MW being transferred from A to B, calculate the flow in the line after outage of a 600 MW generator in system B. 1000 MW A В
A- A 3-ph, double circuit O.H.T.L, 320 kV, 340 km, 50 Hz has a configuration as shown in the figure below where each phase in the double circuit has a double bundle with a spacing of d cm between the two conductors in the bundle where d is the last two digits (from right) of your registration number (i.e for the student that has a registration mumber 202112396, d= 96). Each conductor in the bundle has a diameter of 0.135 ft and a geometric mean radius (Ds = 1.6 cm). Calculate: 1- Inductance per phase per km. 2- Total inductive reactance. 3- This T.L. is required to supply 240 MVA at 0.86 lag P.f. at 320 kV, assuming that this load is divided equally between these two circuits, find the voltage drop across this T.L (ignore capacitive effect in the calculation). 4- What may happen if we replace the location of a' and c' bundles. Discuss your answer. 5- Suggest a way to ređuce the value of the inductance. Verify your suggestion. -8 m 3m 3m 8 m 11 m
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......