2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure. If it is subjected to the two torques , (a) determine the average shear stress in the tube at points A and B. (b) What is the angle of twist of end C? The tube is fixed at E. %3D 3 mm В. 25 N-m 60 mm - 5 mm DI 1.5 m C 3 mm 0.5 m 40 mm (a) 60 N-m

2. A tube is made of aluminum (G = 24 GPa ) and has a rectangular cross section as shown in figure. If it is subjected to the two torques , (a) determine the average shear stress in the tube at points A and B. (b) What is the angle of twist of end C? The tube is fixed at E. %3D 3 mm В. 25 N-m 60 mm - 5 mm DI 1.5 m C 3 mm 0.5 m 40 mm (a) 60 N-m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4-Find the stresses in each direction, also find the change in volume of the block of dimension 110 mm x 50 mm x 31 mm, subjected to 3 mutually perpendicular loads. The load along length, breadth and depth directions are 22 kN (tensile), 30 kN (compressive), 22 kN (compressive) respectively. Take E as 100 GPa, Poisson’s ratio as 0.3 The stress along length direction (Unit in MN/m2)= _____________ The compressive stress along width direction (Unit in MN/m2)= _____________ The compressive stress along depth direction (Unit in MN/m2)= _____________ The change in volume of the block is (unit in mm3) = ______________
A composite shaft consists of a brass sleeve securely bonded to half steel shaft, fixed atend A as shown in Figure 1. The brass sleeve and steel shaft have a modulus rigidity Gb= 40 GPa and Gs = x0 GPa. The length of the assembly is L = 400 mm. The outerdiameters of the shaft and sleeve are d1 = 70 mm and d2 = 90 mm, respectively. Giventhe shear stress of brass is τb = 70 MPa and shear stress of steel is τs = 110 MPa.[Note: x value - Use the last non-zero digit from your group number. If the group numberis zero, use the second last digit instead. For example, if your group number is 5, your xvalue is 5 and Gs = 50 GPa; if your group number is 10, your x value is 1 and Gs = 10GPa.] In this situation, Group number is 2. 1) Write the equations of equilibrium for AB and BC section of the shaft in terms of Twith the help of free body diagrams. 2) Determine the polar moment of inertia for brass sleeve and steel shaft.
None
For the bell crank shown in equilibrium in figure below, determine the normal and shearing stress of the pin at B, if the diameter of the pin is 20mm. 200 mm → 40 KN A 35° Pin at B 250 mm
F3.A shaft is composed of two 6-in. diameter sections coupled together (see figure below). Part AB is bronze and part BC is steel. A torque is applied at the free end which causes a maximum shear stress in the bronze shaft of 10,000 psi. Find the angle of twist of the free end. Assume the modulus of rigidity of bronze is 6 (106) psi and that of steel is 12(106) psi. Bronze Dia. = 6 in. A 3' Steel B Match each item to a choice: Angle of twist T
Q2:The composite torsion member as shown in Fig. If the allowable stresses for steel and aluminium are 84 Mpa and 70 Mpa respectively and if the composite shaft is not to twist more than 1.45°, determine the maximum torque T that can be applied to the member. Gs = 84 Gpa, Ga 28 Gpa. Aluminium Steel 75 .mm 100 mm 1m
A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid steel bar with a diameter of 30 mm. A support at one end of the bar and a hard plate at the other end of the tube hold them both tightly in place. A torque T = 650 Nm acting on the end plate twists the composite bar, which has a height of 850 mm. Assuming that the steel's shear modulus is G = 80 GPa, find the maximum shear stresses in the bar and tube, respectively, and the angle of rotation (in degrees) of the end plate
- once answered Correctly will UPVOTE!!
4. The stepped circular bar shown below is made from aluminum (E = 70 GPa, v = 0.35). Each segment is 400 mm in length. Prior to applying the loads, the bar has the dimensions shown. The structure is axially loaded as shown. Determine the stress in each segment, the maximum stress and its location, the final in length of the structure, and the final diameters of each segment due to the applied loads. All dimensions shown are in mm. Ø 25 40 15 ↑ Fu 300 kN 600 kN 300 kN
Need asap answer
N = 400 N T= 1.8 N-m In order to drill an 8mm hole into a block of steel, a Normal Load of 400N and Torque of 1.8 N-m must be applied to a drill bit. The drill bit H D = 8mm has a diameter of 8mm and is a solid cylinder at point H. Write the stress state for the element H pictured in the diagram.
Two solid circular shafts (i.e., AB and BC) are fixed to rigid walls at point A and C, respectively. Members AB and BC are coupled together through a rigid plate at B. As shown in the figure, an external torque is applied at point B. Determine the absolute maximum shear stress developed in the whole structure AC. Both members AB and BC are made of the aluminum alloy with shear modulus G = 60 GPa. 150 mm 100 mm B 10 mm 5 kN-m Note: ignore the effect of stress concentration. 20 mm