A solid shaft made of aluminum alloy (E=70 Gpa, v=0.33). The diameter of the shaft is 25 mm, and subjected to a torque of T=60 Nm and a compressive force of 10 kN. Find the normal strain in y-direction at point H at the outer surface.

A solid shaft made of aluminum alloy (E=70 Gpa, v=0.33). The diameter of the shaft is 25 mm, and subjected to a torque of T=60 Nm and a compressive force of 10 kN. Find the normal strain in y-direction at point H at the outer surface.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.5.7P: -7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5...

See similar textbooks

Related questions

Q: A 600 N man starts climbing a ladder that placed against a wall as shown. The weight of the ladder…

Q: A large blower for a furnace delivers 47 000 ft/min (CFM) of air having a specific weight of 0.075…

A: Given: V˙ =47000 ft3/min γ=0.075 lb/ft³ To find: W˙ and m˙

Q: The sketch shows a flat plate aligned parallel to an incompressible airstream. Assume a velocity…

A: Given Data: flat plate aligned parallel to an incompressible airstream Find: Assume a velocity…

Q: Find the volume flow rate of water exiting from the tank shown in Fig. 7.12. The tank is sealed with…

Q: 5a 3a. ਹਨ ਧਨ Ja

A: Given system, a= 36 mm using the moment of inertia of rectangle about centroidal axis I=…

Q: 11. Steady-state creep rate data are given below iron at 900 C. &($) 104 10-6 σ (MPa) 17 6.5 If it…

Q: An engine, running at 350 r.p.m., drives a line shaft by means of a belt. The engine pulley is 950…

Q: A continuous and aligned fiber-reinforced composite is to be produced consisting of 42 vol% aramid…

A: a

Q: A bird enthusiast is watching a bird in flight as shown. Determine the velocity and acceleration of…

A: Given velocity of bird watcher = 2 ms acceleration of bird watcher = 1 ms2 velocity of bird = 2 ms…

Q: In the figure, the slender bar (1), with a mass of 30 kg, is attached to the sphere (2), with a mass…

Q: 50 mm OW. 50 mm 50 mm 350 mm 50 mm Determine the moment of inertia about the centroidal x-axis shown…

Q: Solar collector 2 W₁ RAD 3 Turbine 4 Condenser Q

Q: Vipretion

Q: A velocity of a vehicle is required to be controlled and maintained constant even if there are…

A: Given situation is

Q: 19. Find the loss of head in the pipe entrance if speed of flow is 10 m/s. OA. 5.10 m OB. 10.2 m O…

Q: The ears of a rabbit can be thought of as two rectangular fins that dissipate heat. The dimensions…

Q: The engineer shown in the figure has a mass of 70 kg, and his bicycle, an aluminum Alubike, weighs…

A: Given: To find: Velocity

Q: 6) A speed limit sign along a highway is shown in the figure. Calculate the bending moment at the…

Q: A cylinder of 0.40-ft radius rotates concentrically inside a fixed cylinder of 0.42-ft radius. Both…

Q: 1. Consider the structure shown, which was designed to support a load. It consists of a boom AB with…

A: Only one question is allowed to solve as per the

Q: W M 84 X m

A: Given, To find the equation of motion using Langrange's approach we need to find the Kinetic…

Q: Find out the rate of heat generation in n highly exothermic fuel rod of 2.4 m length and 15 mm…

Q: Take that a = 36 mm. (Figure 1) Figure ▼ Part A Iy= 5a Determine the moment of inertia of the beam's…

A: Introduction The area moment of inertia is a two-dimensional plane form feature that describes its…

Q: Which of the following is NOT an impact of IP infringement? O O O O Loss of market share O damage to…

A: Due to IP infringement there will be loss of market share because same products manufactured by…

Q: 13.38 A row of regularly spaced, cylindrical heating ele- ments is used to maintain an insulated…

A: Given: D = 10 mm S = 20 mm h = 200 W /m2K T1 = 500 K Te = ? T2 = 300 K T∞ = 450 K

Q: 5 KN 30 10 kN 10 KN с 1.90 B 5 SAN 15 AN 10 KN 90% E F 30

Q: For the crude oil ship shown: if the empty ship weight =10000T and its length of 200m. Find the…

A: Given: Length of the ship→L=200 m Width of the ship→w=50 m Depth of the ship in the water→d=8 m…

Q: For the problem related to Fundamental.4, a sketch of the considered system showing and naming (or…

A: Given-Information:- rA = 8 inrB = 50 inDistance = 10 inα = At2.3 rads2vp = 28 in s-1 To-Determine:-…

Q: The boom in the figure below (Figure 1) weighs 3000 NN and is attached to a frictionless pivot at…

Q: In which direction will the "X" begin to move when the handle is operated as shown? a) b) c) d) AJUD…

Q: 7. A volume of 450 cc of air is measured at a pressure of 740 mm HG absolute and a temperature of 20…

A: Given:Initial volume, V1=450 ccInitial presssure, P1=740 mm HGInitial temperature,…

Q: Exercise 4.1.1 Consider a mass m acted on by two springs and dashpots as shown in Figure 4.5. Assume…

Q: 23.A machine has a selling price of P500,000 after given 15% discount. Find the original amount.

Q: What is the cooling curve for both metals and plastics?

A: Cooling Curve: A cooling curve is a line graph that represents the change of phase of matter,…

Q: 9.82 The front door of a dishwasher of width 580 mm has a vertical air vent that is 500 mm in height…

Q: A student sits on a freely rotating stool holding two dumbbells, each of mass 2.97 kg (see figure…

Q: 1.) dx dt + 7x = 5 cos 2t 2 ← Equation 1

A: Given equation is a 1st order differential equation with x as dependent variable and t as the…

Q: Solve the for the support reactions for the beams shown.

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29000 ksi; I = 376…

Q: An electron is at rest in an oscillating magnetic field along the z-direction with B₂-Bo cos(wt)…

A: Given, An electron is at rest in an oscilllating magnetic fieldis, B→= Bocos w+k^Where Bo…

Q: A slender, rigid bar of mass m and length I is pinned to a massless collar as shown in the figure…

A: Solution: Given Data: To Find: Acceleration of the collar.

Q: Obtain the value of Ufg at 250C, in kj/kg, directly from the steam tables. Ufg = ? kj/kg

A: Ufg should be determined using the steam tables. Ufg is the difference between internal energy of…

Q: (4) BIA 30 disk: radius = r = 0.350m r BIA = 0.300m rad: length= L = 0.90 A disk and a rod are…

A: Given data: A disk and slider arrangement is given such that VA = 3.6 m/s Find: (a) The angular…

Q: m ks): A vibrating system consists of a mass of 17.5 kg, a spring of stiffness C Q5 35.0 N/cm, and a…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: Water at 40°F is flowing downward through the fabri- cated reducer shown in Fig. 7.11. At point A…

A: Given:Water temperature, T=40oFVelocity at point A, VA=10 ft/sPressure at point A, PA=60 psig=60*144…

Q: Example 2.2: A four cylinder, a 2.4L engine that operates on a four-stroke cycle at 3200 RPM. The…

A: Disclaimer: “Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: Assuming the dynamic model of a of a one-link robot arm is given as: 1 "1 ma²0+ mga sin 0 where m,…

A: Given model,

Q: a) The velocity component of an incompressible and 2-dimensional flow is given by Determine u = -x +…

Q: In both words and equations, state the two conditions which must be satisfied for a rigid body to be…

A: 1.The resultant of all external forces must be zero.∑F=0 2.The resultant of all external torques…

Q: (MO14) 4. Design a quick return mechanism with 270 cm stroke, time ratio of 3, fixed link length of…

A: Consider the given data, Crank length, s= 97.5cm Time ratio, t=3 Fixed link length, l=75cm Stroke,…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
Solve Problem 7.7-12 by using Mohr’s circle for plane strain.
A circular steel tube with an outer diameter of 75 mm and inner diameter of 65 mm is subjected to torques 7"at its ends. Calculate the maximum permissible torque 7jliajl if the allowable normal strain is ea= 5 X 10"4 Assume that G = 15 GPa.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
-7 A steel tube (G = 11.5 x 106 psi) has an outer diameter d2= 2.0 in. and an inner diameter dt=1,5 in. When twisted by a torque 7", the tube develops a maximum normal strain of 170 x 10-6. What is the magnitude of the applied torque T?
Solve the preceding problem if the cube is granite (E = 80 GPa, v = 0.25) with dimensions E = 89 mm and compressive strains E = 690 X l0-6 and = = 255 X 10-6. For part (c) of Problem 7.6-5. find the maximum value of cr when the change in volume must be limited to 0.11%. For part. find the required value of when the strain energy must be 33 J.
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A statically indeterminate stepped shaft ACE is fixed at ends A and B and loaded by a torque TQat point C (see figure). The two segments of the bar are made of the same material, have lengths L4and LB, and have polar moments of inertia IAand Ipb. Determine the angle of rotation 4>of the cross section at Cby using strain energy. Hint: Use Eq, (3-55b) to determine the strain energy Urn terms of the angle d?. Then equate the strain energy to the work done by the torque to. Compare your result with Eq. (3-52) of Example 3-9.
Solve the preceding problem if the length L = 56 in., the inner radius r1— 1.25 in., the angle of twist is 0.5°, and the allowable shear strain is 0.0004 rad.
Derive a formula for the strain energy U of the cantilever bar shown in the figure. The bar has circular cross sections and length L. It is subjected to a distributed torque of intensity t per unit distance. The intensity varies linearly from r = 0 at the free end to a maximum value t = /0 at the support.
A thin-walled hollow tube AB of conical shape has constant thickness I and average diameters dAand dBat the ends (see figure). Determine the strain energy U oT the tube when it is subjected to pure torsion by torques T, Determine the angle of twist of the tube. Note: Use the approximate formula / ird^tlA for a thin circular ring; see Case 22 of Appendix E.