2. A sump pump turning at 1600 rpm provides a water discharge of 9gpm againts a head of 18ft. Compute the minimum power input. Use the curve below to detremine the efficiency. 1.0 10,000 0.8 1000 300 100 0.6 30 mas 0.4 10 - Q = 5 gal/min 100 300 1000 3000 10.000 30.000

2. A sump pump turning at 1600 rpm provides a water discharge of 9gpm againts a head of 18ft. Compute the minimum power input. Use the curve below to detremine the efficiency. 1.0 10,000 0.8 1000 300 100 0.6 30 mas 0.4 10 - Q = 5 gal/min 100 300 1000 3000 10.000 30.000

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Provide an example list of Laminar and Turbulent Flow.

A: ● Laminar flow is a smooth flow which flows without any interference or intermixing of fluid layers ...

Q: 3. A fluid enters with a steady flow of 3.9kg/s and an initial pressure of 690 kPa, density of 3.2 k...

Q: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, whi...

Q: The tabulating machine which uses punch cards during 1890AD is ____? a) Pascaline b) Difference Engi...

A: Data cards, commonly known as punch cards, are used to convey information to machines.

Q: 5. Types of Grinding Wheel Machines and their outputs. (atleast 3)

A: Types of grinding machine: Floor or bench grinder: This is a small type of machine used in the works...

Q: 14. Given the three vectors A, B, and D, show that: Ā - (B + D) = (Ã · B) + (Ã · D) 15.Determine the...

Q: What is the problem arise when design a pneumatics system with more than 1 cylinder and What are the...

Q: 150 kg C A 200 kg B 300 kg

Q: A steel cylindrical air receiver with 6.0 feet diameter and pressure load of 220 psi., design stress...

A: Answer: The bursting steam pressure of this air receiver is 1711.11 psi.

Q: urated steam with temperature of 160.1111 oC. Locate the pressure and specific enthalpy. (Use moll

A: Given: A saturated steamTemperature of steam, T=160.1111o C

Q: value of spring constant K needed

A: Given;Uniform stiff rod of length,l=300 mm having a weight= 300 NIt is pivoted at one end and connec...

Q: A river section shown has an initial volume of 600m with 750g of phosphorus. The discharge from the ...

A: (a) Write the discharge from upstream. Q1=100 m3day2gm3=200 g/day

Q: na power generation plant. Use the figure below to ma- ipe sizes for the suction and discharge lines...

A: given Q =400 gal/min from figure we select following suction pipie ...

Q: Steam enters a turbine stage with an enthalpy of 3628 kJ/kg at 70 m/s and leaves at the same stage w...

Q: 8.3 A rectangular block of material is subjected to a shear stress of 30 MN/m2 together with its ass...

Q: Find the force acting at points B and O if given F = 540 N. 1D find Bx 2) Find By 3) Find Ox 4) Find...

Q: A metal plate 10 mm thick at 30°C is suddenly expose heat flux of 3000 W/m2 and the other side is ex...

A: Thickness t=10mmt=30°CHeat flux=3000W/m2Heat transfer coefficient =50W/m2kDensity=8933kg/m3Specific ...

Q: A random sample of 83 reconstructed clay vessels from the Turquoise Ridge archaeological site indica...

Q: of 60 kW. The evaporating temperature is -5degC and condensing te

A: givenT1 =5°Cx1=1v1=vg=0.061 m3/kgk1=247 KJ/kgs1 =0.94 KJ/kg-kT2 = =35°cP2 =Psat@ 35°c=1610 KPaP2 =16...

Q: (d) A long cord of negligible mass is wrapped around a third pulley, Pulley C, and attached to a spr...

A: Given datacord are negligible massFs-Constant Force

Q: a. A gear of 80 teeth and a pinion of 20 teeth has a gear and pinion ratio of 4. Find the tooth thic...

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked . K...

Q: 3) Compute the centroid of the shaded area shown in figure Q.3 y R50 R30 120 100 25 50

Q: (c) Describe the steps involved in establishing a CFD approach to the determination of air movement ...

A: The CFD approach means Computational fluid Approach. In this approach, the CFD study is necessary to...

Q: Provide a general description of Induction Furnaces used in Industrial Manufacturing of Steel

Q: Does line AB intersect with parallel lines YZ and WX? Complete all views

Q: A 5.31 horsepower rating No. 40 roller chain has an input through a 12-tooth sprocket turning at 1,8...

Q: What is the problem arise when design a pneumatics system with more than 1 cylinder?and What are the...

A: Soln -The problem arise when we design a pneumatic systwm with more than one cylinder is the, pressu...

Q: using generalized Vogel's equation. The fol- ata are given: r pressure, p = 5,500 psia oint pressure...

A: Well A : pwf1>pb J* =q1p¯ -pwf1 =4005500-4000=0.2667 stb/day/psi qb=J*p¯ ...

Q: Draw a graph showing the elasticity, flexibility, and brittleness property in terms of stress and st...

A: Stress -strain diagram show various type stages- Brittle material- Non-ductile material- Ductile ma...

Q: In your own words, explain why the internal combustion engine made by Etienne Lenoir is the most sig...

A: Etienne Lenoir

Q: a dry, 2.4 den, mature wool fiber has reached its maximum tenacity value. How many grams would it ta...

A: Write the given data. ρ=2.4 den

Q: Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, whi...

A: Find the diameter of the pipe at section 2.

Q: D. How many Btu need to be added to change 5 lb of ice at 30°F to steam at 215°F? Refer to tables fo...

Q: Determine the approximate load on a cooling tower if the entering and leaving temperatures are 96°F ...

A: The approximate load on a cooling tower is 2000 BTU/min. Therefore, option (b) is correct answer.

Q: Write shear & moment equations as function of x and draw shear & moment diagrams for the beam given ...

Q: The position of a particle traveling along a curved path is s = (3t? - 4t? + 4) m, where t is in sec...

Q: Saturated water vapor at 200.111 oC is isothermally condensed to a saturated liquid in a piston-cyli...

Q: Molly earned a score of 940 on a national achievement test. The mean test score was 850 with a stand...

A: Given data, μ=850 ( Mean score ) σ=100 ( Standard Deviation ) Molly score = x = 940 To find P...

Q: STATICS AND STENGITH OF MATERIALS Question: Determine the moment of the force F about: a) Point A. 4...

Q: Hello could anyone teccomend any improvements to thid type of rankie cycle combustion chamber fuel H...

Q: Briefly cite the differences between the recovery and recrystallization processes.

A: Annealing- It isla heat treatment process in which the steel is heated to 50-100°C above austenitic ...

Q: A duct of rectangular cross-section 600mm X 400mm carries 90 m3/min of air having a density of 1.2 k...

A: Given data Rectangular Cross-section of duct = 600 mm * 400 mm discharge = 90 m3/min density = 1.2 ...

Q: The wheel of 4 ft. radius shown in the figure rolls freely to the right. At the given position, w = ...

A: Find the acceleration of point B. Given data :- Angular velocity - 3 rad/sec Angular acceleration -...

Q: a) Derive the radial equation of motion in terms of radial force per unit mass ƒ (r)

A: Write the expression of radial acceleration. ar=r¨-rω2

Q: 3.)A particles position is defined by the equation s = 4t² + 2t + 6 m where t is in seconds. Find th...

A: Given: The particle position is given by equation s=4t2+2t+6. The time is t=5 s. The velocity is e...

Q: Find the value of heat, efficiency rate, work in 68 spin and power in 0.87 seconds if an engine rele...

Q: A) Explain 1) Different types of Keys 2) Interference fit 3) Couplings.

A: (1) In this case, we will answer the all subparts (up to 3) of the part A. Please resubmit the quest...

Q: Find the brake power of the engine running at 755 rpm. The iength of lever from centre of pulley is ...

Q: On a hot day the wood surface gets heated to 50°C to a considerable depth. Sudden sharp showers cool...

A: Given data as per the question The temperature of the heated surface =500 c Temperature of surface a...

Q: Problem 1. In following truss, determine the internal forces of members EG, ED, BC, and DF. State wh...

Concept explainers

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.

Question

COMPLETE SOLUTION.

2. A sump pump turning at 1600 rpm provides a water discharge of 9gpm againts a head of 18ft.
Compute the minimum power input. Use the curve below to detremine the efficiency.
10,000
0.8
1000
300
100
0.6
30
ma
0.4
10
Q = 5 galmin
100
300
1000
3000
10.000
30.000

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge pipe 4" in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read -4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6" suction pipe.
1. An axial flow water pump is based upon the free-vortex design. The mean diameter velocity diagram has an axial inlet with a flow coefficient of 0.3 and a work coefficient of 0.208. The tip diameter to mean diameter and the hub diameter to mean diameter ratios are 1.25 and 0.75 respectively. The blade velocity at the mean diameter is 60 m/s. Find and draw the velocity diagrams at the mean, hub and tip diameters. Show all velocities and angles on the velocity diagrams. {..
B/ Find the flow rate in units of L/s that an axial piston pump delivers at 1000 rpm. The pump has nine, 15 mm diameter pistons arranged on a 125 mm diameter piston circle. The offset angle is set at 10% and the volumetric efficiency is 94%.
A pump with a volumetric displacement of 4 in^3/rev runs at 3600 rpm and produces 1500 psi. The actual flow rate is 59 gpm. What is the volumetric efficiency of this pump? Enter a whole number percentage.
2. A sump pump turning at 1600 rpm provides a water discharge of 9gpm againts a head of 18ft. Compute the minimum power input. Use the curve below to detremine the efficiency. 1.0 10,000 0.8 1000 300 100 0.6 30 ma 0.4 10 Q = 5 galfmin 0.2 100 300 1000 3000 10.000 30.000
2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
2) A double acting cylinder is hooked up in the regenerative circuit shown. The relief valve setting is 1500 psi. The piston area is 20 in2. and the rod area is 10 in2. If the pump flow is 0.25 gpm, Find: a) The cylinder speed in ft/s for the extending stroke, The load-carrying capacity in pounds for the extending stroke, c) The output power in HP for the extending stroke. Find the cylinder speed in ft/srfor the retracting stroke, e) The load-carrying capacity in pounds for the retracting stroke, The output power in HP for the retracting stroke.
Q No. 5: The diameter of side of a pump is 6 inches and that of the intake pipe is 8 inches. The pressure gauge at discharge reads 30 psi and vacuumed gauge at intake reads 10 inches of Hg. If Q=3cfs of water and the brake horsepower is 35. Find the efficiency of the pump. There are no losses. Note : Please Solve as Per Question's Statement. Need a Neat and Clear Solution.See Attached Picture For Detail .
Include a free body diagram. pump draws water from a sump through a vertical 6′′ pipe. The pump has a horizontal discharge pipe 4′′ in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read —4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6′′ suction pipe. (ANSWER: 10.7 Hp, 2.4 ft)
Solve fast with Proper Equation. 1. A centrifugal pump delivers 2.5 cfs of water against a head of 25 ft at 1500 rpm and requires 10 hp. If the speed is reduced to 1250 rpm calculate the power , assuming the same efficiency. Select one: a. 17.3 kW b. 13.7 kW c. 5.8 kW d. 8.5 kW
URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by step solution. Box the final answers. Do not shortcut your solution. I will give an upvote if it satisfies. Thank you! If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a. What is the head of the pump if the velocity is 4 m/s and the pressure is 90 kPa on the suction side of the pump? b. How much power is required to drive it if the diameter of the suction side is 600mm? c. If the pump is rated at 120hp, what is the efficiency of the pump neglecting energy losses in the system?
A centrifugal pump equipped with a variable frequency (speed) drive running at 3500 rpm is discharging 240GPM corresponding to a head of 287ft. The horsepower is 35.5. if the pump's speed is reduced to 2900 rpm, what will be the revised flow rate? Select the correct response: 176.21 gpm 76.21 gpm 89.66 gpm 98.85 gpm 289.66 gpm 198.86 gpm