Determine the approximate load on a cooling tower if the entering and leaving temperatures are 96°F and 88°F, respectively, and the flow rate of the water over the tower is 30 gpm. 3,000 BTU/min 2,000 BTU/min O 2,500 BTU/min O 1,500 BTU/min

Q: process planning is known as

A: Given; Following are the option given, Where,   Given question is;  During development of a product…

Q: how do you workout the linear interpolation from process 1-2 the step by step working would be…

A: Given data:- Inlet condition of turbine P1 = 8 MPa T1 = 480 °C To find:- the linear interpolation…

Q: What to do before creating a design concept?

A: Before creating a design concept

Q: The company produced a new product intended to measure diameter profiles. In a run test conducted,…

A: 1). Precision- option B is correct Accuracy is how close or far off a given set of measurements are…

Q: 2. Before developing possible solutions, an engineer usually _________________. A. communicates his…

A: Before developing possible solutions, an engineer usually _________________

Q: Which one of the following type of benchmarking is least likely to resuit in any major breakthrough…

A:

Q: (a) In engineering practice, which one is the most common used in product architecture? Modular…

A: a) (a) In engineering practice, which one is the most common used in product architecture?

Q: What is the testing plan for universal testing machines? How are the tests to be done is planned in…

A: Procedure for testing a sample in the universal testing machine

Q: Describe ideal design process and explain briefly. What are design inputs?

A: Design is the method of conversion of raw material into useful product through a proper selection of…

Q: Exoskeletons (which may also be referred to as exosuits, exosystems, industrial human augmentation,…

A: To explain:Evaluate the following alternatives based on your criteria, and justify your selection…

Q: Perform FMEA and Root Cause Analysis for any TWO problems faced in your industry.

A: introduction; FMEA is a failure mode and effect analysis. FMEA quality tools enhance the quality of…

Q: I need answers to these 3 parts for a review activity.

A: An italic f indicates finish, the v symbol and check mark type symbol also represents the surface…

Q: What are the financial benefits are reported by the organization after the successful implementation…

A: Six sigma is a quality-control process used by business organizations as a statistical benchmark to…

Q: As a reliability engineer, your job is to help the plant to achieve its goals. Improving…

A: Maintenance of reliability allows a person, specifically a reliability engineer, to profit from…

Q: An accident investigation report must include all of the following except: The date of the accident…

A: Detailed explanation:The question presents a list of four items and asks which one is not a required…

Q: Tolerance is .. Your answer Clearance is . Your answer Why it is important to generate a number of…

A: To Discuss:  a) Tolerance b) Clearance c) Why it is important to generate a number of alternatives…

Q: What indices do we use to evaluate the control quality?

A: There are many indices in quality control which are important to evaluate the quality as well as…

Q: en writing up the engineering design process which are necessary to include

A: Engineering design process

Q: 6. Design for , that is, the load can be taken by other members or the effect of fatigue failure…

A: Solution to first three sub-parts as per our company policy.

Q: In Agile: O All code should be written before test plans are created in case changes in the code…

A: Agile is an iterative approach where the entire project team participates in each and all…

Q: I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps…

A: 13.Calculate the maximum material condition for the largest cylindrical part feature.

Q: Assume yourself as a drilling fluid engineer working in a company, you asked to drill a well for…

A: Parameters that are considering while drilling a well......

Q: OM A customer has recently tightened the specs for a part your company supplies. The specs are now…

A: Explanation: 1.Firstly identify the clause in revised specification which is very critical.  2.So if…

Q: What term describes a numerical value that can be applied to a dimensional constraint in a technical…

A: Variation process arranging approach is some of the time called an information recovery strategy.…

Q: How Do We Approach an Engineering Design Problem?

A: Following are the steps used for approaching an engineering design problems are:   1.Define the…

Q: What are the significance of tolerance and allowance in production process? Diagram?

A: Tolerance and Allowance

Q: What is the relation between product tolerance and product variation?

A: Process variation is the watched difference from part-to-part which is caused by the restrictions…

Q: Explain the following with appropriate examples (at least 2 examples) 1. Grubler's criterion. 2.…

A: The Grubler's criterion gives the number of degrees of freedom of a mechanism involving links and…

Q: a) Explain what is meant by a "Six Sigma Quality Level". Use a nomal distribution to illustrate your…

A: a) Six Sigma - It is a methodology and symbol of quality. It is a quality philosophy and the way of…

Q: Discuss six sigma maintenance and lean maintenance in detail. Both should be explained with relevant…

A: Six Sigma Maintenance and Lean Maintenance are most commonly employed to improve the efficiency and…

Q: Q/What is the design process flow chart

A: Using a diagram known as a process flowchart, the steps of a complicated process may be shown in…

Q: The probability that a product operate within an expected timeframe is the dimension of quality…

A:

Q: Beam deflection is to the length to a beam. OA. flexure

A: Explanation As we know that the deflection of any beam always follow the equation of elastic curve…

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at  45o  with 0.250” leg distance.

Q: QUESTION 4 External failure quality costs occur when customers discover a defect. Which of the…

A:

Q: There are two types of scales in aerial photographs, mention and explain them briefly

A: There are two types of scale in aerial photographs: i) large scale photograph ii) small scale…

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.