Problem 1. In following truss, determine the internal forces of members EG, ED, BC, and DF. State whether the member is in tension or compression.

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Write the mathematical expression for the Brinell hardness test. HB=2PπDD-D2-d2 Here, Applied load…

Q: , I want to know what would be the perfect size to put a bushing in a hole. The bushing will have a…

A: To find-: The perfect size to put a bushing in a hole. Given-: The dimension of the hole is h=0.50…

Q: Q1: Find the resultant force and the component force F for the system shown below (fig 1) using…

A: Calculated the resultant force and the component of force F for the system using parallelogram law.

Q: A tank (contains a fluid of density=1318.4 kg/m3) stands on a frictionless cart (The cart is fixed)…

A:

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: 4 (7) Czar (10) 8

A: Given: There is shown a milling machine in which we have to find out the different names of the…

Q: For the stress element below, when a = 6, b = 4, and c = 6, the principal stress σ1 , the largest…

A:

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: 3

A:

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: A disk of mass, m, and radius, R as shown in the figure is being supported by an elastic shaft with…

A:

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: LA 5 mm 28 mm ー-ギー - 49 mm 49 mm

A: For triangle, X1= 0 Y1= (1/3)×95= 31.67 mm  A1 = 1/2 × 98× 95 = 4655 mm2 For semi circle, X2 =0 Y2=…

Q: Determine ly and ky.

A:

Q: 15 kN 20 kN 2 m m

A:

Q: Q1 The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket…

A:

Q: Figure Q4 shows the values of the normal and shear stresses acting on a certain stress element which…

A: Given: Normal Stress in x direction→σx=-1.5 MPa Normal Stress in y direction→σy=1 MPa Shear stress…

Q: 6xty- 2

A: Information given⇒ 6x4y-22x-1y42

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: 1- Draw Torque vs. angle of twist for steel specimen

A: INTRODUCTION : Whenever the specimen subjected to the twisting moment that is torque, the stress…

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: A force F = 6980 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the…

A:

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: 13378.2898 lbm to lbf

A:

Q: A piezometer and a pitot tube (close to each other, as described in the figure) are connected to the…

A:

Q: 4. The weight of the box is W = 90 N and the coefficient of static friction between the box and the…

A:

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.