2. A distributed load of W N/m is applied over the entire length of a simply supported beam 4m long. The beam has a cross section shown. -200- 20 120 160 20 -160- a. Which of the following gives the value of "W" so that it will not exceed an allowable flexural stress of 10 MPa. b. Which of the following gives the value of "W" so that it will not exceed an allowable shearing stress of 0.80 MPa. c. Which of the following gives theh value of "W" so that the screws have a shear strength of 800 N and a pitch of 50 mm.

2. A distributed load of W N/m is applied over the entire length of a simply supported beam 4m long. The beam has a cross section shown. -200- 20 120 160 20 -160- a. Which of the following gives the value of "W" so that it will not exceed an allowable flexural stress of 10 MPa. b. Which of the following gives the value of "W" so that it will not exceed an allowable shearing stress of 0.80 MPa. c. Which of the following gives theh value of "W" so that the screws have a shear strength of 800 N and a pitch of 50 mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

NOTE: PLEASE ANSWER ALL OF THE QUESTIONS AND PROVIDE STEP BY STEP SOLUTION
Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.99 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 11.7 ft and P = 92.21 kips. Round off the answer to five decimal places. 010.png В D F h H C E G -on-- 9 ft→9 ft→9 ft→-9 ft- P P
Determine the largest weight W that can be supported by the two wires AB and AC. The allowable working stresses are 180 MPa for AC and 120 MPa for AB. The cross-sectional area of AB is 500 mm2 and that of AC is 300 mm2. Show the solution. Correct answer is 60.23kN
Consider the beam below. If the beam is subject to a 20kN internal shear force, determine the maximum shear stress (in MPa) in the beam. The thickness of all pieces is 30mm.
4 A metal wire Im long and of 10mm diam eter is stretched by a load of 50 kg. If E = 7 x 10³ N/mm² for the metal, find the (a) stress (b) strain and (3) Poisson's ratio if the lateral strain is 2.6x 105 m/m.
The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square cross- section and that each pin has a 14mm diameter, determine the maximum value of the average normal stress (a) in member BE. (b) in member DF. 50 kN 40 kN 2m 2m 2m B 1.5m Answers should be in MPa.
Mechanics of deformable bodies.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. STRENGTH OF MATERIALS The piece of plastic is originally rectangular. After the application of force, it deformed in the position shown. If a = 2 mm, b = 1.5 mm, and c = 4 mm, determine the normal strain in diagonal BC and the shear stress in corners A and C.
A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15 kips. The beam has length L = 6 ft. (a) Calculatethe principal normal stresses and the maximumshear stress for an element located at C near the fixedsupport. Neglect the weight of the beam. (b) Repeat Parta for point D which is 4 in. above point C (see figure).See Table F-1(a), Appendix F, for beam properties.
A frame is built with members ACB and DC to support load P as shown. Member DC has a rectangular cross section with width of 25 mm and thickness t. Stress-strain curve for the material of which the member DC is made is also provided below. a. Determine the thickness t so that member DC does not yield. (You can assume same behavior for compression and tension)b. Determine the diameters of the pin A and D if allowable shear stress for pins is ???? = 40 ???.
Q3
Find the question, thanx.