H.W #4: The lap joint shown in figure is fastened by five 25 mm diameter rivets. Determine the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 175 MPa, the bearing stress in the plate to 140 MPa, and the tensile stress in the plate to 132 MPa. P 120 mm 30 mm 180 mm 30 mm P

H.W #4: The lap joint shown in figure is fastened by five 25 mm diameter rivets. Determine the maximum safe load P that can be applied if the shearing stress in the rivet is limited to 175 MPa, the bearing stress in the plate to 140 MPa, and the tensile stress in the plate to 132 MPa. P 120 mm 30 mm 180 mm 30 mm P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 12 A plate is fastened to a fixed member by four 16mmP rivets arranged as shown. Compute the maximum shearing stress developed in the rivets. 30KN 100mm spacing 30KN
4. Six rivets are used in the connection shown in the figure. If both P= 50 kN, what is the minimum diameter P- 50 rivet is necessary so as not to exceed the 70MPA allow shearing stress? What thickness of plate is required so as not to exceed a bearing stress of 140 MPa? 80 mm 80 mm Ps so 100 mm
A plate is fastened to a fixed member by four 16mmO rivets arranged as shown. Compute the maximum shearing stress developed in the rivets. See figure 12. * 30KN 100mm spacing 30KN Figure 12
Problem 2 Given is a truss structure: Where: • Working shear stress for the rivets is 70 MPa • Working bearing stress due to rivets is 140 Mpa • Thickness of the member is 5 mm • Thickness of the Gusset plate is 6 mm Rivet diameter is 15 mm Determine the no. of rivets to fasten the member BD 80 N 120 N 200 N 4 Pands 4m - 16 m
Six rivets are used in the connection shown in the figure. If both P=50KN, what is the minimum diameter rivet is necessary so as not exceed the 70MPa allow shearing stress? What thickness of plate is required so as not exceed a bearing stress of 140MPA? p= 50 80 mm 80 mm 100 mm
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
Determine (a) the shear stress in the rivets and (b) the thickness "t" of the steel plate if the allowable bearing stress between the rivets and the plates is 110 MPa. 5-12 mm ø 50 KN 200 mrm o o o 50 KN 50 KN-C 50 KN
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
(N) 32900
43 OSFu A tension member with an allowable tensile stress of 0.6Fy is connected to the gusset plate using four rivets having a diameter of 34mm. Assume the diameter of the hole is 2mm more than the rivet diameter. It is required to determine the value of b so that the net width along rivets 1-2-3-4 is equal to the net width along 1-2-4. > Determine the value of b > Determine the most critical net area The value of T without exceeding the allowable stress. Gusset plate If failure will occur in djagonal s 2 direction add a value 4g C0mm b. 6. 100mm 400mm 100mm 100mm 12mm 150mm
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
7. The bracket shown is welded on one side of a steel column with 800mm of 6mm fillet weld. Determine the maximum shear stress on the weld. If the allowable stress si 400 MPa what is the allowable load that the connection can carry? 44 kN 300 mm F.W. ON NEAR SIDE F.W. ON FAR SIDE F.W. ON FAR SIDE F.W. ON NEAR SIDE 200 mm 200 mm