beam AB supporting two concentrated loads P has a rectangular cross section of width b = 100 mm and the height h = 150. The distance from each end of the beam to the nearest load is a = 0.5 m. the span of the beam is 5 m. Determine the maximum permissible value P (in kN) if the allowable stress in bending is 11 MPa (for both tension and compression) FINAL ANSWER IN 3 DECIMALS

Q: Portions of a 0.25 × 0.25-in. square bar have been bent to form the two machine components shown.…

A:

Q: A tubular aluminum alloy [G= 4,000 ksi] shaft is being designed to transmit 480 hp at 2,700 rpm. The…

A: Given values: Power, P = 480 HP Speed, N = 2700 rpm G = 4000 ksi = 576000 kip/ft2 Maximum shear…

Q: At the proportional limit, a flat bar with a cross- section of 5mm x 45 mm elongates 2.5mm in a…

A: write down the given data cross-sectoin of the barA=45×5=225mm2axial loadP=50…

Q: The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was…

A:

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

A:

Q: A structural beam subjected to sagging bending has a cross section which is an unsymmetrical I…

A:

Q: The two vertical rods attached to the light rigid bar are identical except for ength. Before the…

A:

Q: W16

A:

Q: A steel beam, of lengths a= 4 m and b=4 m and a hollow box cross section, is supported by a hinge…

A: Given  a= 4 m  b= 4 m  q= 4.2 KN/ m

Q: 0,3in 0.4in2 3P 2P + C. Find the albwable säfe p if the stresses in the bar are the following: AB 50…

A:

Q: The uniform rod is subjected to the axial loads as shown. Which segment has the absolute maximum…

A: Given Loads To find out Which segment has Maximum normal stress

Q: (d) Radius of Mohr's circle (e) maximum value of the principal stress omax at the junction of the…

A: Question is based on the simply supported beam subjected to concentrated load at center. Properties…

Q: Determine the largest permissible value of P for the beam and loading shown, knowing that the…

A:

Q: A B C 80 kN 2 m 50 kN D E F -1m--1 m--1 m--1 m-|

A:

Q: The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G= 39 GPa). Knowing that portion CD…

A:

Q: Knowing that a factor of safety of 3.01 teel structure shown. Member AB ha Use Yield Stress a, 250…

A:

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A:

Q: The pin-connected structure shown consists of a rigid bar ABCD and two axial members. Bar (1) is…

A:

Q: The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal…

A: Given Data Three suspender bars are givenCross-sectional area A=450 mm2Young's modulus E=70 GPaTwo…

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD 2- if Beam Weighs is not know then finding of…

Q: Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice…

A: Consider the figure,

Q: A

A:

Q: 1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter…

A:

Q: 7. The pin-connected rigid rods AB and BC are inclined at 0 = 30° when they are unloaded. When the…

A:

Q: • Consider a beam of rectangular cross-section (h×b) and length L. The beam is loaded by force T =…

A: step 1-

Q: 400 kN -0.5 m- -0.5 m A B 0.4 m D E F

A:

Q: (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 142 (kips) is applied. The…

A: Given Data: The load applied on the beam is, P=142 kips   To Determine: The stress in the aluminum…

Q: As shown in the figure below, determine the internal loadings at points A,B and. Consider the…

A: To determine the internal loading at points A and B of the given structure.   Given, Parameter FN =…

Q: A timber beam 150 mm wide by 250 mm deep is

A:

Q: 9. The rigid bar ABC is supported by a pin at A L=4 ft and a steel rod at B. A = 0.5 in.2 E= 29 x106…

A:

Q: NOTE: PLEASE ANSWER ALL OF THE QUESTIONS AND PROVIDE STEP BY STEP SOLUTION

A:

Q: Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed…

A:

Q: The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

A:

Q: member (see figure). The column is 10 A long. The force acting at the top of the column has an…

A: Solution:- Given,W8*35 wide flange memberColumn is long L=10ftA=10.3 in2Eccentricity e=1.15inFactor…

Q: P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam…

A: b = 130 mm h = 200 mm  P = 25 KN w = 30 KN/m

Q: Determine the largest weight W that can be supported by the two wires AB and AC. The allowable…

A: Given data in question  Stresses Area Angles To find out  Weight W value

Q: 4 A metal wire Im long and of 10mm diam eter is stretched by a load of 50 kg. If E= 7x 10³ N/mm² for…

A: Given Data  Load (P) = 50 kg  Modulus of Elasticity (E) = 7 × 103 N/mm2  Length of wire (L) = 1m…

Q: Determine the magnitude of the pin force at A. Assume W = 640 Ib, a = 3.5 ft, b = 2.6 ft, r = 8 in.…

A: Step 1

Q: The truss shown consists of wooden members. Knowing that each member has a 100 x 100 mm. square…

A:

Q: The three suspender bars AD, BE, and CF are made of the same material (E = 70 GPa) and have equal…

A:

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: : Determine the appropriate weigh

A: