17. Dental implants are metal fixtures, typically a threaded stud (screw) surgically fastened to your jawbone below the gums, onto which artificial teeth can be mounted. These metal implants become anchored to your bone through osseointegration (the bone fuses to the metal). Implants replace the roots of missing teeth and support single crowns, large bridges, or dentures. To ensure the implant is adequately anchored to the jawbone, the dental surgeon checks the strength of the connection by measuring the resistance to movement by using a torque wrench. The required torque is 35 N-cm. Convert the required torque to Ibr-inches. (report result to one decimal place)

17. Dental implants are metal fixtures, typically a threaded stud (screw) surgically fastened to your jawbone below the gums, onto which artificial teeth can be mounted. These metal implants become anchored to your bone through osseointegration (the bone fuses to the metal). Implants replace the roots of missing teeth and support single crowns, large bridges, or dentures. To ensure the implant is adequately anchored to the jawbone, the dental surgeon checks the strength of the connection by measuring the resistance to movement by using a torque wrench. The required torque is 35 N-cm. Convert the required torque to Ibr-inches. (report result to one decimal place)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Define thixotropic.
A composite beam is fabricated by bolting two 3.8-in-wide by 8-in.-deep timber planks to the sides of a 0.5-in. by 8-in. steel plate. The moduli of elasticity of the timber and the steel are 1720 ksi and 28700 ksi, respectively. The simply supported beam spans a distance of 17 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD= 3 ft, LBC = 11 ft, b = 3.8 in., d = 8 in. and t = 0.5 in. (a) Determine the maximum bending stresses 0₁, os produced in the timber planks and the steel plate if P = 2.2 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1210 psi and 26900 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.)
13. Why are steel bridges not electroplated, whereas jewelry and cutlery are electroplated?
[15 pts] 6) A cylindrical rod having a diameter of 8 mm is to be deformed using a tensile load of 19 kN. It must not experience plastic deformation and a diameter reduction of more than 7.5x10-3mm. Of the materials listed as follows, which material meets the conditions? Material Modulus of Elasticity (GPa) Yield Strength (MPa) Poisson's Ratio Aluminum alloy 70 200 0.33 Brass alloy 101 300 0.34 Steel alloy 207 400 0.30 Titanium alloy 107 650 0.34
I need help with parts J and K, I will rate immediately. Thank you.
Referring to the dial gauge shown in Figure , determinea. Accuracyb. Sensitivityc. Range, given that the small pointer moves one division for each full turn of the large pointerd. Which of the preceding items can be improved through calibration?e. For measuring devices, which of the following two statements is always true?(i) Accuracy cannot exceed sensitivity(ii) Sensitivity cannot exceed accuracy
b) In engineering practice, it is often required that two sheets or plates are joined together and carry the load in such ways that the joint is loaded. Many times, such joints are required to be leak proof so that gas contained inside is not allowed to escape. A riveted joint is easily conceived between two plates overlapping at edges, making holes through thickness of both, passing the stem of rivet through holes and creating the head at the end of the stem on the other side. Discuss each of the rivet joints listed below: i) Tearing failure of plates ii) Bearing failure of rivets 2 iii) Shear failure of rivets iv) Splitting/cracking failure of plates at the edges
Calculate quantity of the Reinforcing for the beam shown in figure below. A 0.3 m 3.2 m 2016 08 @ 230 mm c/c 60 cm 2018 23 cm Section A -A 0.3 m 0.6 m
Date: Course: Time: Pind the vertical movement os is 120 KN Stsel Aluminum 3 m Im B P=120 kat Aluminum A = 900 mm² E = 70 GN m² steel A= 600 mm E 200 GNM² %3D
Using Animated Figure 6.19 estimate the (a) Brinell hardness (in HB), and (b) Rockwell hardness (in HRB) for a brass alloy having the stress-strain behavior shown in Animated Figure 6.12. а.) і HB b.) HRB
I looked up this problem for help and am confused with the part i circled in red. im blanking. why use the (4*3)/3(pi) and in the A4 (4*1)/3(pi)?
I thought it was the opposite. Why is the steel rod the diameter of the tube?