The wood beam supports loads of w = 460 lb/ft and P = 860 lb on span lengths of LaB = 10.8 ft, Lgc = 5.4 ft, and LcD= 5.4 ft. The beam cross section has dimensions of b; - 1.0 in., dz - 3.0 in., b2 - 5.2 in., and d2 - 9.30 in. Determine the magnitude and location of: (a) the maximum horizontal shear stress in the beam. (b) the maximum tensile bending stress in the beam. di d2 B LAB LBC LCD b2 Answer: (a) Tmax" psi (b) Omax" psi

The wood beam supports loads of w = 460 lb/ft and P = 860 lb on span lengths of LaB = 10.8 ft, Lgc = 5.4 ft, and LcD= 5.4 ft. The beam cross section has dimensions of b; - 1.0 in., dz - 3.0 in., b2 - 5.2 in., and d2 - 9.30 in. Determine the magnitude and location of: (a) the maximum horizontal shear stress in the beam. (b) the maximum tensile bending stress in the beam. di d2 B LAB LBC LCD b2 Answer: (a) Tmax" psi (b) Omax" psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following are the properties of a steel section to be used for a beam section:Fy = 248 MPa Area = 21300Ix = 300000000 Iy = 98800000Sx = 2080000 Sy = 746000d = 289 tw = 19.2tf= 31.8 bf = 265w beam in kN/m = 9laterally unsupported length, Lb = 3 m 1. What is the minimum unsupported length of the beam to be considered long? a. 16.2 m b. 14.5 m c. 13.6 m d. 12.8 m 2. What is the critical depth over thickness ratio set by NSCP? a. 206.68 b. 126.68 c. 106.68 d. 16.68 3. What is the allowable bending stress in the given beam section? a. 148.8 b. 163.68 c. 142.68 d. 124.68 4. If the laterally unsupported length been 10 m, what is the allowable bending stress as per NSCP 2001? a. 148.8 b. 163.68 c. 142.68 d. 124.68
600 150 150 Refer to the figure shown. Given are the following: Unit weight of concrete = 24 kN/m fe' = 35 MPa fse = 820 MPa fpu - 1,350 MPa Aps = 1,200 mm? foy = 1.080 MPa Beam is a simple span and have a length = 30 m. Determine the design moment capacity of the section. (kN-m) 00L
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN Please solve your Solution in a handwritten Note: It should be handwritten pleaseeee
W 14 x 142 is used as a column having a length of 8.48 m. long. It is hinged at the r end and fixed at the lower end but there is a lateral bracing perpendicular to minor axis of the W section at a point 4.78 m. above the bottom support. It is assumed to be pinned connected at the bracing point. Using A 36 steel Fy= 248 MPa the NSCP Specificatioris. E, = 200000 MPa. Properties of W 14 x 142 A = 26967.69 mm2 d= 374.65 mm bf= 393.70 mm tf= 27.00 mm tw= 17.27 mm4 Ix= 695.11 x 106 mm4 Iy = 274.71 x 106 mm4 rx = 160.53 mm rY = 100.84 mm Assume: Kx = 0.80 for 8.48 m. length KY = 1.9 for the length on the upper support KY = 0.80 for the length on the bottom support Compute the slenderness ratio along y-axis. Please show clear solution thank you
pls reply fast thank you
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The beam is A36 steel with yield strength Fy = 248 MPa. The beam is not restrained against lateral buckling. The beam is W 21 by 62 steel shape, whose relevant properties are shown below: r = 0.053 m d = 0.533 m bf = 0.210 m tf = 0.016 m S = 0.002077 m3 Given this condition, solve for the allowable flexural stress in the compression flange. Use Cb = 1 as should be taken conservatively
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN
SOLVE please Determine the design bending strength of ISLB 350 @ 486 N/m, considering the beam to be laterally supported. Assume factored design shear force will not exceed 0.6 times the design shear strength of the cross-section. If it is used as simply support beam of unsupported length 5 m then determine the factored distributed load the beam can carry. Use Fe410 grade steel For ISLB 350 @ 486 N/m, section properties are as follows: h = 350 mm; b= 165 mm; t₁ = 11.4 mm; t = 7.4 mm; R₁ = 16 mm; Izz = 13158.3 × 104 mm²; I = 631.9 × 10¹ mm²; Zpz = 851.11 × 10³ mm³; Zez = 751.9 x 10³ mm³
Determine the maximum load that an 8 foot long 2"x4" rectangular aluminum alloy bar (E = 10.5x10^3ksi, σY = 40 ksi) can support with a factor of safety of 3 for both crushing and buckling if it has endconditions of:a. Pinned-pinned.b. Pinned-fixed.c. Fixed-free.d. Fixed-fixed.
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
A composite beam spans a distance of L= 12 ft and is fabricated by adhering two wooden boards (b= 2 in., d= 8 in. and E = 1,500 ksi) to the sides of a steel plate (t = 0.4 in., d = 8 in. and E= 30,000 ksi). 400 lb 400 Ib 200 lb/ft d -3 ft- 3 ft V (lb) -6ft 600 400 (ft) 12 -400 -600 1. For the given loading condition, determine the maximum normal stress M (lb-ft) in the steel plate. A) 3,850 psi +x (ft) B) 1,550 psi -300 C) 2,250 psi D) 4,200 psi -1200 - 1200 E) None of the Above 2. If the allowable normal stress of the steel is 9,000 psi and the 200 lb/ft distributed load remians constant, determine the largest acceptable concentrated load on each end. A) 1,600 lb B) 2,325 lb C) 935 lb D) 860 lb E) None of the Above