Answered: Calculate quantity of the Reinforcing…

Calculate quantity of the Reinforcing for the beam shown in figure below. A 0.3 m 3.2 m 2016 08 @ 230 mm c/e 60 cm 2018 23 cm Section A -A 0.3 m 0.6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: b= 10.1 in 1= 0.855 in The variables a and b are defined by the last two digits of your Z-number.…

A: Design of Tension member as per IS: 800-2007 Given: A992 steel a= 4; b = 1 so, L = (10+4) =14 in Ag…

Q: 30 20kN PVC Wood 20kN 50mm

Q: A cylindrical rod is designed of A36 steel (Ftall=Allowable tensile stress=24ksi). What is the…

A: To Determine Smallest reasonable sized rod that could support the 15,000 pounds, R

Q: D = 875 kN L = 1450 kN SECT. 2 SECT.1 Square Tubing Pipe Fy = 290 mPa Do 4.8m So S, = outide…

A: Question is not clear. Please upload the full question so that the understanding in problem may…

Q: Determine the compressive force (in Ib) in the bars shown after a temperature rise of 154°F if d =…

Q: Compute for the linear weight of 10 mm reinforcing bar. (Use the unit weight of the Steel). o 0.692…

A: Given data in question Diameter Steel bar To find out Linear weight Note Unit weight of steel =…

Q: in each segment. 4P Steel Aluminum 1.75' 2.75' 2.50' Bronze Answer: Øst = 13.33 ksi, OBr = 1

Q: A double riveted lab joint single strap (chain riveting) shown in the figure. Given that th rivet…

A: Dia=12 mms=10 mm

Q: 2. Based on the figure below, a steel rod was fitted on the copper tube and was fixed with a washers…

Q: Use hand written solution. Nscp 2015 steel design ty

A: To solve the problem of determining the load capacity of the column made of two channels C250×30…

Q: From the figure shown which of the following gives the best outside dimension of the square tubing…

A: Given: Length of the column, L = 4.8 m Support condition: One end is fixed and the other end hinged…

Q: Q2/ Find (x) so that the rigid beam remains in a horizontal position. Steel L = 3m A = 500mm? E =…

Q: A 6m long solid bar of circle section has 140mm diameter for aluminum for length of 4m, while it has…

A: Length of the solid bar= 6m Dia of Aluminium = 140mm Diameter for aluminum = 120mm

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

A: Given E= 70Gpa= 70000Mpa

Q: A compound bar, 1.5m long is made up of three concentric square components A, B and C, fitted…

Q: Problems (1) Determine the stress in each material if the left wall yields 0.6mm Bronze A=2400mm…

A: Given data in questionLoad 120 and 50 kNSpan 600 , 400 and 300 mm of bronze, aluminum and…

Q: 6. A steel block (E=30 x 10° psi and v=0.29) is loaded under uniaxial compression along x.

A: Mohr's circle is generally the various points that pointing the magnitude of normal and shear stress…

Q: 3. A rectangular steel block is subjected to triaxial loading as shown. If v = 0.3 and E = 200 Gpa,…

A: Solution Givan Data ν=0.3E= 200 GPa

Q: 1. The bolt connection shows 8-22mm diameter bolts in a bolt hole diameter of 25 mm and spaced…

A: No of bolts = 8 Bolt dia d = 22 mm Bolt hole dia do = 25 mm Pitch distance p = 100 mm Gauge distance…

Q: A flat steel bar, 29 mm wide by 4 mm thick and 1.2 m long, is bent by couples applied at the ends so…

Q: diameter of washer = 9/8 inch = stress in the nut 18 ksi g stress 800 psi

A: d=7/8 inch dia of root thread = 0.731 inch din = 9/8 inch tensile stress = 18ksi bearing stress =…

Q: (a) determine the average shear stress and shear strain in each of rubber blocks (b) determine the…

Q: 0.5 mm 350 mm - Bronze A = 1500 mm² E = 105 GPa x = 21.6 x 10-6C 450 mm Aluminum A = 1800 mm² E = 73…

Q: In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a…

Q: Two plates are connected by a bolt as shown in the figure. What is the shear stress on the bolt? D…

Q: Fig3 6cn Į 25 3 cm Tom R 5cm Icm 11 cm

Q: Akuminum rod E= 70 GPa G 26 GPa A 100 mm? a 23,6 x10c 20 N 0.5 m By Bearm ABC El-150 MNm Sm

A: Given:- E=7GPa G=28GPa A=100mm2 alpha=23.6 x 10 -5/oC To find:- deflection and rotation at point C

Q: Two A36 16mm thick steel plates are connected by four rivets shown. 50 0 Pu 50

A: for A36fy=250MPafu=410Mpadesign strength for tension failure on gross…

Q: ble mass is hinged at at C and a steel rod 4 a, A₂ = 900 mm², and Z 1 m steel 2 m B P SM-004 ovement…

Q: 18 in. 6 in. 18 in. Steel B C Steel -Aluminum

Q: Calculate the tensile steel strain of 5-16-mm-dia rebars in a concrete beam 200 mm by 440 mm at…

Q: Q- Calculate the Poisson's ratio of the bar material if a tensile force of 350 kN is applied to it…

A: Given data in question Load 350 kN Change in length and diameter 0.85 & 0.024 mm Length 600mm…

Q: (Problem 2.126 from the text book) Two solid cylindrical rods are joined at B and loaded as shown.…

A: Given Esteel =29 ×106 Psi Ebrass = 15×106 psi Note 1 psi = 1 lb/ in2

Q: e beam is made from a material that can safely support a tensile or c Based on this criterion,…

A: Reactions :∑ MB=0RA1.6-F1=0RA=FA1.6Max moment :MMax=RA1=FA1.6 kN-m

Q: A steel bar 50 mm in diameter and 2 m long is surrounded by a shell of a cast iron 5 mm thick.…

Q: Determine the compressive force (in Ib) in the bars shown after a temperature rise of 164°F if d =…

Q: The part of the shown graph shows no permanent deformation. Select one: a. Black b. Red C. Green d.…

A: The given graph is stress-strain curve of mild steel.

Q: In the figure below, a joint is made by gluing two plywood gussets of thickness t to wood boards.…

A: Given, Tensile working stresses for the plywood =1245psi Tensile working stresses for the boards…

Q: Question 27 An A36 angle bar is used as a tension member connected on both legs with 18 mm diameter…

A: Given:- 12 mm diameter bolts s = 65 mm, Ag = 1852 mm2 t = 8 mm To find:- The design strength (kN)…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Calculate quantity of the Reinforcing for the beam shown in figure below.
A
0.3 m
3.2 m
2016
08 @ 230 mm c/c
60 cm
2018
23 cm
Section A -A
0.3 m
0.6 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Length of longitudinal and lateral steel

VIEW

Step 2: Quantity of reinforcement

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

please answer in the nearest 3 decimal numbers
Help me find the answer to each question related to a truss. And write on a clean paper each, then box the final answer, thank you for helping me
P(kN) 53 A 3 3 find S1,52,53,54, S5 Rod forces.indicate that they are tensile or pressure.Write the results you found in the table below. www ww wm w w ROD FORCE TENSİLE/PRESSURE NUMBER S1 S2 S3 S4 S5 5u
Determine the compressive force (in lb) in the bars shown after a temperature rise of 173°F if d = 0.015 in. Round off the final answer to five decimal places. Use the following data: Bronze Aluminum A = 2.24 sq. in A = 2.78 sq. in E = 14959726 psi E = 10594540 psi L = 12.5 in L = 16.6 in α = 11.61 x 10-6/ °F α = 12.67 x 10-6/°F
Use the following scale for the diagrams: SHEAR DIAGRAM: 1 cm = 100 kN; MOMENT DIAGRAM: 1cm = 100 kN-m F kN Fa kN F kN/m As B DF3 kN-m 1 m 2 m 2 m 2 m R2 3 m 2 m R1 F1 = 72: F2 = 30; F3 = 150;F4 = 60 %3D
What is the maximum concentrated load that can be applied at the end of an embedded hollow pipe, made of AISI 1020 steel? Take 10.16 cm for the outside diameter, and 6.35 cm for the inside diameter. The length of the pipe is 183 cm. Its maximum deflection must not exceed 5.08 cm. Neglect the weight of the pipe. Answer 22816 N
The assembly shown in Figure No. 3 consists of a hollow steel [E = 200 GPa] tube (1) with an outside diameter of 60 mm and a wall thickness of 5 mm, a solid 40 mm diameter aluminum [E= 70 GPa rod (2), and a solid 30 mm diameter aluminum rod (3). The member lengths are L1 2 000 mm, L2 = 1 200 mm, and L3 %D 3D800 mm. The following loads act on the assembly: P = 150 kN, Q = 80 kN, and R = 115 kN. Determine (a) the change in length of steel tube (1). (b) the deflection of joint D with respect to the fixed support at A.
Find the value of p
Determine the maximum tensile stress in the beam shown.
Topic: Stresses in Beams (Given formulae: Fb =Mc / I for bending stress v = VcA' y' / Ib for Shear stress)
A round bar made of same material consists of 3 parts each of 100 mm, length having diameters of 40 mm, 50 mm and 60 mm respectively. If the bar is subjected to an axial load of 10 kN, the total elongation of the bar would be (E is the modulus of elasticity in KN/mm². (a) 4/1 1 1 + + (b) TE 16 25 36 (c) 1 0.4 1 1 + wwwwww + TE 16 25 36 (d) 4√2/1 1 1 www + wwwwwww + TE 16 25 36 40/1 1 1 + TE 16 25 36 — ===== + — mm mm mm mm
An A36 angle bar is used as a tension member connected on both legs with 12 mm diameter bolts. Given that s = 50 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile fracture at the smallest possible net area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm