13. A steel rod of 20 mm diameter passes centrally through a copper tube of external đdiameter 40 mm and internal diameter 20 mm. The tube is closed at each end with the help of rigid washers (of negligible thickness) which are screwed by the nuts. The nuts are tightened until the compressive load on the copper tube is 50 kN. Determine the stresses in the rod and the tube, when the temperature of whole assembly falls by 50°C. Take E, = 200 GPa ;E̟ = 100 GPa ; a̟ = 12 × 104°C and a_ = 18 × 10ʻºC. JAns. 99.6 MPa; 19.8 MPa]|

13. A steel rod of 20 mm diameter passes centrally through a copper tube of external đdiameter 40 mm and internal diameter 20 mm. The tube is closed at each end with the help of rigid washers (of negligible thickness) which are screwed by the nuts. The nuts are tightened until the compressive load on the copper tube is 50 kN. Determine the stresses in the rod and the tube, when the temperature of whole assembly falls by 50°C. Take E, = 200 GPa ;E̟ = 100 GPa ; a̟ = 12 × 104°C and a_ = 18 × 10ʻºC. JAns. 99.6 MPa; 19.8 MPa]|

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Prob 6. The rigid bar below is supported by a pin at E and two rods. The brass rod AC (Ebrass 105 GPa) has a diameter of 30 mm. The copper rod BD (Ecopper = 120 GPa) with a diameter of 60 mm. A load of 40 kN is applied at the end as shown. (a) Determine the stresses in both rods. (b) Determine the vertical displacement of the points C and D. = 1 m 1 m 2 m 1.5 m 1/1 B 0.75 m 40 kN
I need the answer as soon as possible
A clamped edge steel diaphragm of radius 100 mm and thickness 3 mm is subjected to a uniform pressure of 100 KN/m2 on one side. Determine the location and maximum values of deflection, hoop, and radial stresses.
A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A gasket is inserted between the flange at one end of the pipe and a flat plate used to cap the end. How many 25 mm diameter bolts must be used to hold the cap on if the allowable stress in the bolts is 90 MPa of which 50 MPa is the initial stress? What circumferential stress is developed in the pipe?
step-wise solution please
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm² and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 °C to 95 °C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (Est = 200 GPa, Ecu – 100 GPa, as: = 12 × 10-6/ °C, acu = 16 × 10-6/ °C)
A cylindrical pressure vessel is made by shrinking a brass shell over a mild steel shell. Both cylinders have a wall thickness of 6 mm. The nominal diameter of the vessel is 750 mm and is to be used in all calculations involving the diameter. When the brass cylinder is heated 50°C above room temperature, it exactly fits over the steel cylinder which is at room temperature. What is the stress in the brass cylinder when the composite vessels cool to room temperature? E for steel=200 GPA E for brass = 100 GPA a for steel = 12 x 10"/C a for brass = 19 x 106/°C Wrong answers will be downvoted
Determine the stress in the Aluminum rod (Psi) after the load 68 (kips) is applied. The light rigid bar ABCD is pinned at 8 and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free.
A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 10 mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS ? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY, AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECE SSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INITIAL STRESS?
attached can solve wrong
The same circular plate, as in the previous questions, is considered. Assume a plate radius of Ro=490mm and a plate thickness of h=9.64mm, respectively. Also, assume that the plate is subjected to a uniform pressure of P=1,440 KPa, and that the plate is made of a material of Poisson's ratio V=0.34. Find the absolute value of the radial stress at the centre of the plate in KPa. NOTES: type in your answer without considering any negative sign; round-off your answer to 4 decimal places. ↓ r> P Ro VIT