Part A The steel pipe in (Figure 1) has an inner diameter of 2.87 in. and an outer diameter of 3.12 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. ΜΕ ΑΣΦ Η vec ? 01, 02787, 56.4 Submit Previous Answers Request Answer × Incorrect; Try Again; 3 attempts remaining psi, psi

Part A The steel pipe in (Figure 1) has an inner diameter of 2.87 in. and an outer diameter of 3.12 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. ΜΕ ΑΣΦ Η vec ? 01, 02787, 56.4 Submit Previous Answers Request Answer × Incorrect; Try Again; 3 attempts remaining psi, psi

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

The steel pipe in (Figure 1) has an inner diameter of 3.41 in and an outer diameter of 3.66 in. If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe.
The steel pipe in (Figure 1) has an inner diameter of 4.57 in. and an outer diameter of 4.82 in. Figure 12 in. 12 in. 1 of 1 > 60 lb Part A If it is fixed at C and subjected to the horizontal 60-lb force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, to three significant figures. 01, 02 = Submit Provide Feedback Request Answer pai, psi Next >
IN THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A AND B ON THE PIPE ACCORDING THAT THE PIPE'S DIAMETER IS 25 mm; SHOW THE PRIMARY STRESSES AND PRIME AXES (principal axis directions) ON THE MOHR CIRCLE.
Problem 2: For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 02 and, 03) using Mohr's circle. r= 0.0042 m, d = 0.03 m, D = 0.033 m, T= 250 Nm P = 1500 N, M = 300 Nm, A M T J.C₁ P r M T Di d
Forces of Px = 580 lb and Py = 220 lb act on the teeth ofthe gear shown in Figure 1. The gear has a radius of R =6 in., and the solid gear shaft has a diameter of 2.0 in.Using a = 5 in., determine the normal and shear stressesat (a) point H and (b) point K. Show the orientation ofthese stresses on an appropriate sketch.
Determine the stresses at points A and B as a results of applying each of the following internal loads N = 300 N, V = 250 N, M = 120 N.m and T = 300 N/m. The diameter is 20 mm. You must show your detailed solutions
The steel pipe in (Figure 1) has an inner diameter of 3.54 in, and an outer diameter of 3.79 in. Figure 12 in 12 in. 12 in. A B 1 of 1 If it is fixed at C and subjected to the horizontal 60-Ib force acting on the handle of the pipe wrench at its end, determine the principal stresses in the pipe at point A, which is located on the outer surface of the pipe. Express your answers, separated by a comma, three significant figures. 01 0₂ = Submit Provide Feedback V AE Bequest Answer 12 in. + @ 30° ? psi, psi 60 lb Next >
The thin-walled pipe has an inner diameter of 2 in. and a thickness of 0.1 in. It is subjected to an internal pressure of 530 psi and the axial tension and torsional loadings shown in (Figure 1). Suppose that M = 240 lb. ft. 900 lb- M M 900 lb Part A Determine the in-plane principal stresses at a point on the surface of the pipe. Express your answers in kilopounds per squared inch to three significant figures separated by a comma. 17 ΑΣΦ 01,02 = vec ? ksi
Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form a nonuniform rod of total length 100 m, which will be suspended from a support at A as shown. The density of brass is 8470 kg/m^3 Determine normal stresses of ((σzz)AB and (σzz)BC) as a function of z, and draw the variation of stresses with respect to z-axis on the same graph.
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
For the shaft shown below, determine the normal and shear stresses acting on the element located at point A, including stress concentrations. Then draw the stress element at A with the applied stresses and determine the three principal stress (0₁, 2 and, σ3) using Mohr's circle. r = 0.0042 m, d = 0.03 m, D = 0.033 m, T = 250 Nm P = 1500 N, M = 300 Nm, A M M DEHRƏC T d T P P r
The tank shown in the figure shown is fabricated from a steel plate. a. Determine the maximum longitudinal stress caused by an internal pressure of 1.2MPA if the steel plate has a thickness of 10mm. b. Determine the maximum circumferential stress caused by an internal pressure of 1.2MPA, if the stress plate has a thickness of 10mm. c. Determine the minimum thickness plate which maybe used if the stress is limited to 40MPA and the internal pressure is 1.5MPA. 1400 mm 400 mm 600 mm