The rectangular bar is connected to the support bracket with a 12-mm-diameter pin. The bar width is w = 65 mm and the bar thicknes s 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the earing stress in the bar cannot exceed 130 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the naximum value of Pmax that can be supported by the structure.

The rectangular bar is connected to the support bracket with a 12-mm-diameter pin. The bar width is w = 65 mm and the bar thicknes s 15 mm. Each side of the bracket has the same dimensions as the bar. The average shear stress in the pin cannot exceed 115 MPa, the earing stress in the bar cannot exceed 130 MPa, and the bearing stress in the bracket cannot exceed 150 MPa. Determine the naximum value of Pmax that can be supported by the structure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

step-wise solution please
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 11 mm and an allowable normal stress of 165 MPa. Pipe (2) has an outside diameter of 48 mm, a wall thickness of 7 mm, and an allowable normal stress of 75 MPa. Assume x₁ = 2.9 m, x₂ = 1.5 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Answer: Pmax (1) B KN
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t= 0.1250 in. The average shear stress in the pin cannot exceed 40 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly. Pulley support bracket Answer: Pmax i ! kips %3D
Determine the stress in the Aluminum rod (Psi) after the load 68 (kips) is applied. The light rigid bar ABCD is pinned at 8 and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free.
In the figure shown, determine the normal stresses at AD and BC + , shearing stress at bolt D bearing stress of AD at bolt D * bearing stress of member EDC at bolt D All bolts Ø16mm 04 im C 0.25 02 m 20kN E 10 x 50 mm 8 x 36 mm
A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
The rectangular piece of wood, 84 mm by 180 mm, is used as a compression block. The grain of the wood makes a 21.2º angle with the horizontal, as shown in the figure. Determine the largest axial force P (in N) that can be applied safely if the allowable stresses on the plane of the grain is 16.4 MPa for compression. Round off the final answer to three decimal places.
The same circular plate, as in the previous questions, is considered. Assume a plate radius of Ro=490mm and a plate thickness of h=9.64mm, respectively. Also, assume that the plate is subjected to a uniform pressure of P=1,440 KPa, and that the plate is made of a material of Poisson's ratio V=0.34. Find the absolute value of the radial stress at the centre of the plate in KPa. NOTES: type in your answer without considering any negative sign; round-off your answer to 4 decimal places. ↓ r> P Ro VIT
Consider tow circular rods with a 50mm diameter are joined by a knuckle joint by a pin of 40mm in diameter. If a tensional force of 120kN are applied at each end of the rods, Determine the allowable tensile stress in the circular rods and the Average shear stress occurs in the pin.
A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side of the pulley support bracket has a thickness of t = 0.2500 in. The average shear stress in the pin cannot exceed 35 ksi, and the bearing stress in the pulley support bracket cannot exceed 70 ksi. Determine the maximum value of Pmax that can be supported by the assembly.
A 2m long bar with square cross section of side 40 mm is subjected to compressive stress of 70 MPa along three mutually perpendicular directions. Take Young's modulus as 200 GPa and Poisson's ratio as 0.3 for the material. Determine change in volume. O a. 1.344 mm3 O b. 1.344 m³ O c. 1344 mm³ O d. 1344 m³
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is